Part 21 Builders licence demerit grounds for occupational

Part 2.1 Builders licence demerit grounds for occupational item 2.1.1 fail to comply with building code, vol 1, cl B1P1 or vol 2, cl H1P1 in damage not minimised as demonstrated by deformation in single element of brickwork, blockwork, or stonework, laid in mortar causing crack or split in joint if— (a) crack or split wider than 3mm; or (b) face of element on either side of crack or split out of alignment with opposite face across crack or joint by more than 3mm creation of defective single masonry element—cracked or split more than 3mm item 2.1.2 fail to comply with building code, vol 1, cl B1P1 or vol 2, cl H1P1 in damage not minimised as demonstrated by deformation in single element concrete floor or structural concrete element causing crack or split in joint if— (a) crack or split wider than 5mm; or (b) face of element on either side of crack or split out of alignment with opposite face across crack or joint by more than 5mm creation of defective single concrete element—cracked or split more than 5mm 2.1.3 fail to comply with building code, vol 1, cl B1P1 or vol 2, cl H1P1 in damage not minimised as demonstrated by deformation in wall, wall render, wall lining, wall tiling, ceiling lining or cornice causing crack or split in joint creation of defective wall or wall render, lining or tiling, or ceiling lining or cornice— cracked or split item 2.1.4 fail to comply with building code, vol 1, cl B1P1 or vol 2, cl H1P1 in damage not minimised as demonstrated by possibility of instability or collapse of primary building element susceptible to termite attack because not provided with code-compliant termite risk management system failure to protect primary building element with compliant termite management system 2.1.5 fail to comply with building code, vol 1, cl F1P2, F1P4, F2P1 or F3P1 or vol 2, cl H2P1 (2), H2P2 or H2P3—surface water, water or dampness could occur in building other than under code failure to protect a building from water or dampness 2.1.6 fail to comply with building code, vol 1, cl F1P1 or vol 2, cl H2P1 (1)—surface water collected or concentrated by building not disposed of in code-compliant way that avoids damage or nuisance to another property, or likelihood of damage or nuisance defective surface water collection or concentration disposal that damaged or caused nuisance or likelihood of either to other property item 2.1.7 fail to comply with building code, vol 1, cl F1P3 or vol 2, cl H2P1 (3)—drainage system for disposal of surface water did not, in code-compliant way— (a) carry water to appropriate outfall; or (b) avoid entry of water to building; or (c) avoid water damaging building defective drainage system— failure to carry water to appropriate outfall, avoid entry of water to building or avoid water damaging building 2.1.8 fail to comply with building code, vol 1, cl E2P1 or vol 2, cl H3P2— building without code-compliant automatic warning on smoke detection creation of building without effective smoke alarm 2.1.9 fail to comply with building code, vol 1, cl F2P2 or vol 2, cl H4P1— water not stopped from penetrating behind fittings, linings or concealed spaces of sanitary facilities, bathrooms, laundries and other wet area facilities defective wet area waterproofing or water containment item 2.1.10 fail to comply with building code, vol 1, cl F5P1 or vol 2, cl H4P2— height of room or other space more than 50mm less than code requires ceiling height more than 50mm too low 2.1.11 fail to comply with building code, vol 1, cl F7P1 to F7P4 or vol 2, cl H4P6—floor, wall or floor or wall penetration do not comply with code sound transmission and insulation requirements defective sound transmission or insulation arrangements 2.1.12 fail to comply with building code, vol 1, cl D1P2 (c) (v) or vol 2, cl H5P1 (b) (iii)—geometry of stairway risers or goings do not satisfy code safe passage requirements creation of unsafe step or stairway 2.1.13 fail to comply with building code, vol 1, cl D1P3 or vol 2, cl H5P2— barrier required under code to prevent people falling not provided defective or no safety barrier item 2.1.14 fail to comply with building code, vol 1, cl G1P2 or vol 2, cl H7P1 or H7P2—swimming pool over 300mm deep without code compliant safety barrier or water recirculation system creation of swimming pool with defective or no safety barrier, or water recirculation system with defective or no safety measures to avoid entrapment or injury 2.1.15 fail to comply with building code, vol 1, cl C1P2 or vol 2, cl H3P1— building with element that does not comply with code to avoid spread of fire to exit, sole-occupancy unit or public area or between buildings or in building defective or no fire spread avoidance measures 2.1.16 fail to comply with Building Act 2004, s 37A (2)—carried out or supervised building work without displaying sign carrying out or supervising building work without displaying sign item 2.1.17 fail to comply with Building Act 2004, s 37A (5)—carried out or supervised building work without replacing or repairing damaged sign within 2 days or prescribed period carrying out or supervising building work without replacing or repairing damaged sign within 2 days or prescribed period 2.1.18 fail to comply with Building Act 2004, s 42 (1) (c)—mortar joint in mortar-jointed masonry element not between 8mm and 12mm wide or bed joint not horizontal creation of defective masonry joint—mortar joint not between 8mm and 12mm wide or bed joint not horizontal 2.1.19 fail to comply with Building Act 2004, s 42 (1) (c)—beam, doorway, window, wall, column, post or truss erected out of plumb creation of out of plumb beam, doorway, window, wall, column, post or truss 2.1.20 fail to comply with Building Act 2004, s 42 (1) (c)—floor, ceiling, beam or sill erected out of horizontal creation of out of horizontal floor, ceiling, beam or sill 2.1.21 fail to comply with Building Act 2004, s 42 (1) (c)—floor, ceiling or beam erected so surface not flat creation of floor, ceiling or beam without flat surface item 2.1.22 fail to comply with Building Act 2004, s 42 (1) (d)—building erected more than 100mm but less than 300mm away from position relative to boundaries indicated on approved plans building siting on approved plan by more than 100mm but less than 300mm 2.1.23 fail to comply with Building Act 2004, s 42 (1) (d)—building erected 300mm or more away from position relative to boundaries indicated on approved plans building siting on approved plan by 300mm or more 2.1.24 fail to comply with Building Act 2004, s 42 (1) (d)—part of floor erected more than 100mm higher or lower than level indicated on approved plans failure to comply with floor level on approved plan by more than 100mm 2.1.25 fail to comply with Building Act 2004, s 42 (1) (d)—top of building erected more than 300mm higher than height indicated on approved plans building height requirements of approved plan by more than 300mm item 2.1.26 fail to comply with Building Act 2004, s 42 (1) (d)—location of structural element, wall, window or door, relative to building erected more than 100mm away from position on building indicated on approved plans or in position where plans indicate other element to be erected failure to comply with set out requirements of approved plan for structural element, wall, window or door by more than 100mm, or inclusion of unplanned structural element, wall, window or door 2.1.27 fail to comply with Building Act 2004, s 42 (1) (d)—lineal dimensions of window, door or doorway erected more than 100mm larger or smaller than lineal dimension of window, door or doorway indicated on approved plans dimensional requirements of approved plan for window, door or doorway by more than 100mm 2.1.28 fail to comply with Building Act 2004, s 42 (1) (d)—beam, doorway, window, wall, column, post or truss in approved plan not erected failure to include significant building element from item 2.1.29 fail to comply with Building Act 2004, s 42 (1) (f)—carried out building work when not builder in commencement notice and not under supervision of builder in notice carrying out building work when not in commencement notice or supervised by notice builder 2.1.30 fail to comply with Building Act 2004, s 43 (2)—proceeded with building work above dampcourse level although certifier has not received required document or is not satisfied that position of building or level of all floors comply with approved plan and any condition failure to provide survey plan or document or comply with approved plan or condition before building above dampcourse 2.1.31 fail to comply with Building Act 2004, s 43 (3)—proceeded beyond stage of building work without giving written notice to certifier or without certifier’s written permission to proceed failure to give written notice to certifier about reaching inspection stage or obtain written permission before proceeding 2.1.32 fail to comply with Building Act 2004, s 64—did not comply with stop notice failure to comply with stop notice item 2.1.33 fail to comply with Building Act 2004, s 64—did not comply with notice to produce survey plan failure to comply with notice to provide survey plan Building surveyors licence demerit grounds for occupational discipline—Act, s 55 (1) (a) Part 2.2 Part 2.2 Building surveyors licence demerit grounds for item 2.2.1 fail to comply with Building Act 2004, s 24, s 28A (4) or s 37 (6)— certifier failed to give registrar required notice failure to notify registrar as required under Building Act 2004 2.2.2 fail to comply with Building Act 2004, s 28—certifier failed to issue building approval when should have, or issued building approval when no grounds to issue failure to issue required building approval, or issue of unauthorised building approval Part 2.2 Building surveyors licence demerit grounds for occupational discipline—Act, s 55 (1) (a) item 2.2.3 fail to comply with Building Act 2004, s 28A (1) or (2)—certifier issued building approval that was not, or not entirely— (a) marked on, attached to, or partly marked on and partly attached to, plans in relation to which approval was issued; or (b) marked on plans and certifier did not indicate on plans that approval, or part of approval, in separate document failure to mark, attach or annotate building approval required detail on approved plan 2.2.4 fail to comply with Building Act 2004, s 30—certifier issued building approval that allowed building work that would contravene law because of external design or siting of building issuing improper building approval—building work would contravene law because of external design or siting 2.2.5 fail to comply with Building Act 2004, s 37 (5)—certifier failed to issue building commencement notice as required failure to issue building commencement notice as Building surveyors licence demerit grounds for occupational discipline—Act, s 55 (1) (a) Part 2.2 item 2.2.6 fail to comply with Building Act 2004, s 44 (1)—received notice that licensee reached stage of building work but did not inspect the building work as soon as practicable failure to do required inspection as soon as practicable after receiving notification about it 2.2.7 fail to comply with Building Act 2004, s 44 (2) (a)—certifier satisfied that building work not compliant with Building Act 2004, s 42, but did not give licensee in charge of building work written notice in accordance with s 44 (2) (a) failure to give written notice in accordance with Building Act 2004, s 44 (2) (a) 2.2.8 fail to comply with Building Act 2004, s 44 (2) (b)—building work complied with Building Act 2004, s 42, but certifier did not certify compliant or give certificate of compliance to licensee in charge of work failure to give certificate of compliance after finding compliant work during required inspection 2.2.9 fail to comply with Building Act 2004, s 50—certifier failed to notify registrar of contravention of building approval or development approval in accordance with s 50 failure to notify registrar of known contravention of building approval or development approval Part 2.2 Building surveyors licence demerit grounds for occupational discipline—Act, s 55 (1) (a) item 2.2.10 fail to comply with Unit Titles Act 2001, s 22B (3) (b)—fail to give copy of unit title assessment report to territory planning authority within 5 working days after giving report to applicant failure to give copy of report to authority within 5 working days after giving report to applicant Part 2.3 Drainers licence demerit grounds for occupational item 2.3.1 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C2P1—sanitary drainage system that does not ensure sewage is transferred from a sanitary plumbing system to an approved disposal system sewage conveyed from sanitary plumbing system to approved disposal system 2.3.2 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C2P6—sanitary drainage system that does not avoid blockage or uncontrolled blockage or uncontrolled item 2.3.3 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C2P7—sanitary drainage system that does not avoid— (a) damage from root penetration, superimposed loads or ground movement; or (b) damage to existing buildings or siteworks; or (c) damage to the Network Utility Operator’s sewerage system another approved disposal system. damage 2.3.4 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C2P3—sanitary drainage system that does not ensure access for maintenance or access for maintenance or item 2.3.5 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C2P4 (1)—sanitary drainage system designed, constructed or installed in way that failed to provide ventilation to avoid likelihood of foul air or gases accumulating in the sanitary drainage system or sewerage system system without adequate ventilation of foul air or gases 2.3.6 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C2P5—sanitary drainage system that— (a) does not ensure protection against internal contamination; or (b) does not avoid the entry of water, foul air and gases from the system into a building; or (c) does not avoid the entry of surface water, subsurface water and stormwater into the system protection from internal contamination, or avoid entry of water or gases item 2.3.7 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl D1P1 or D1P2— sanitary drainage system that— (a) creates undue noise; or (b) does not reduce the transmission of airborne or impact generated sound; or (c) compromises the required sound insulation of a floor or wall by incorporation or penetration of the system. sanitary drainage system that creates undue noise, does not reduce transmission of sound or compromises required sound insulation 2.3.8 fail to comply with Water and Sewerage Act 2000, s 16—provided sanitary drainage service without giving required notice of intention to start or completion of sanitary drainage work 2.3.9 fail to comply with Water and Sewerage Regulation 2001, s 7 (1)— did work on sanitary drainage system other than in accordance with work other than in accordance with approved plan item 2.3.10 fail to comply with Water and Sewerage Regulation 2001, s 8— (a) did not tell registrar when sanitary drainage work ready for inspection; or (b) did not leave sanitary drainage work ready for inspection as failure to tell registrar sanitary drainage work ready for inspection or to leave work 2.3.11 fail to comply with Water and Sewerage Regulation 2001, s 9 (1)— did not test sanitary drain in accordance with AS/NZS 3500 before it was to be passed by an inspector or, if the sanitary drain was altered or repaired, before the alteration or repair was to be passed failure to test sanitary drain before inspection 2.3.12 fail to comply with Water and Sewerage Regulation 2001, s 9 (3)— did not rectify sanitary drainage work found to be defective sanitary drainage work found by test item 2.3.13 fail to comply with Water and Sewerage Regulation 2001, s 10—did plan within required time for sanitary drainage work completed in accordance with the plumbing code completed sanitary drainage work Electricians licence demerit grounds for occupational discipline—Act, s 55 (1) (a) Part 2.4 Part 2.4 Electricians licence demerit grounds for occupational item 2.4.1 fail to comply with Electricity Safety Act 1971, s 4 connection of electrical installation to network before installation inspected, tested and passed 2.4.2 fail to comply with Electricity Safety Act 1971, s 5 electrical wiring work not compliant with electrical wiring rules 2.4.3 fail to comply with Electricity Safety Act 1971, s 6 failure to test electrical wiring work or give required test report Part 2.4 Electricians licence demerit grounds for occupational discipline—Act, s 55 (1) (a) item 2.4.4 fail to comply with Electricity Safety Act 1971, s 8 (7) failure to comply with direction to make installation or work safe and compliant 2.4.5 fail to comply with Electricity Safety Act 1971— (a) s 12 (1) (a) (ii) and (b); or (b) s 12 (2) (a) (ii) and (b); or (c) s 13 (a) (ii) and (b). installation or connection of unsafe prescribed article of electrical equipment to electrical installation Part 2.5 Gasfitters licence demerit grounds for occupational item 2.5.1 fail to comply with Gas Safety Act 2000, s 8 requiring work to be done under AS 5601, cl 2.5.2—provided outlet not connected to gas appliance and not sealed with plug, cap or blank flange failure to appropriately seal surplus gas outlet 2.5.2 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cls 3.2.1 and 3.3.6—material used to join components of consumer piping system, or to connect to consumer piping system, with incompatible mating screw threads or noncompliant joint creation of noncompliant joint in, or connection to, consumer piping system item 2.5.3 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cls 4.1.3, 4.3.1 (c) and 4.4—material of consumer piping system, or connecting to consumer piping system, not adequately protected from corrosion or isolated from incompatible material creation of part of consumer piping system, or connection to it, without compliant corrosion protection or isolation between incompatible material 2.5.4 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 4.1.12—pipework forming part of consumer piping system required to have compliant markings and did not have them failure to adequately identify gas pipework 2.5.5 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 4.2.4—pipework forming part of consumer piping system with diameter too small to achieve required available gas pressure creation of part of consumer piping system with noncompliant pipework size item 2.5.6 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 4.3—inadequate spacing or strength of devices supporting or restraining, or intended to support or restrain, consumer piping system failure to adequately support or restrain gas pipework 2.5.7 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 4.6—part of piping system required to have adequate pressure protection device creation of consumer piping system with defective gas pressure protection 2.5.8 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 4.7—gas vent located in noncompliant position, or so could discharge gas in prohibited way, or no required gas vent provided creation of noncompliant gas vent discharge point or failure to provide required gas vent item 2.5.9 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cls 4.8.2 and 4.8.3—gas hose assembly connection point located— (a) in bedroom, bathroom, sauna, toilet or hallway; or (b) in place where traffic across hose; or (c) if used for space heater—1m or less from doorway creation of gas hose assembly connection in noncompliant location 2.5.10 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 4.9.2—quick-connect type gas connection point installed outside in way that possible for rainwater and debris to enter it creation of quick-connect gas device outside with likelihood of entry of water or debris 2.5.11 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 4.11.3—part of consumer piping system located less than 25mm from metal electrical conduit, metal-armoured or metal-sheathed electrical wire or cable, or electrical earthing electrode creation of part of gas pipework less than 25mm from electrical installation item 2.5.12 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 4.11.11—part of consumer piping system exposed to potential liquid discharge (eg from water heater relief valve or condensate drain) creation of part of gas pipework exposed to liquid 2.5.13 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cls 5.2.4, 5.3.1 and 5.4— (a) gas appliance’s ventilation inadequate to ensure appliance’s safe operation; or (b) possibility that operation of ventilation system, air distribution system or air blower could deprive gas appliance of air required for combustion or caused air pressure to be less than atmospheric pressure at appliance or otherwise adversely affected appliance’s operation; or failure to provide gas appliance with compliant air ventilation or adequate combustion air supply item (c) gas appliance installed at location without adequate ventilation for complete combustion of gas, proper fluing or maintenance of ambient temperature of immediate surrounds at safe level, under normal operating conditions; or (d) air supply to gas appliance contaminated with gases produced by fuel combustion, or contained chemicals or flammable vapours that could have affected combustion; or (e) gas appliance in room or enclosure required to have 1 or more of following, but did not: (i) natural ventilation direct from outside the room or enclosure; (ii) natural ventilation from nearby room or enclosure; (iii) mechanical ventilation item 2.5.14 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 5.2.5—gas appliance installed other than in accordance with manufacturer’s instructions installation not in accordance with manufacturer’s instructions 2.5.15 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 5.2.6—gas appliance installed but failure to install component or install in compliant way may have affected safe operation creation of potentially unsafe gas appliance installation item 2.5.16 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cls 5.2.7, 5.3.4 and 5.12—gas appliance installed so that— (a) surface temperature of nearby combustible surface could exceed 65˚C above ambient temperature because of use of appliance; or (b) appliance is hazard to walls, nearby surfaces, curtains, furniture or opened door; or (c) clearance from appliance, including any flue, to anything else less than required installation too close to combustible surface or other hazardous thing item 2.5.17 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cls 5.2.13, 5.2.15, 5.2.18, 5.2.19 and 5.12— gas appliance installed— (a) so that supported on, or secured to, structure that not durable, or otherwise inappropriate; or (b) so that supported or secured in way that does not minimise strain on any gas pipe connection; or (c) so that not secured or stabilised in way suitable for its conditions of use or in accordance with manufacturer’s instruction (eg upright stove not prevented from tilting when oven door open and lent on; or (d) but not restrained, or restrained in noncompliant way if required to be restrained against rolling on wheels, rollers or castors creation of gas appliance with noncompliant support, security, restraint or stability item 2.5.18 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 5.3.11 (c) and (d)—gas appliance in roof space not provided with compliant access walkway— (a) of required dimensions from point of access into roof space to gas appliance and around appliance; and (b) with no duct intruding on it; and (c) capable of supporting person’s weight; and (d) permanently fixed to building failure to provide compliant walkway to roof space gas appliance 2.5.19 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 5.3.11 (f)—gas appliance in roof space without required artificial lighting or lighting switch located adjacent to, and within 600mm from closest edge of, access opening into roof space failure to provide required compliant artificial light to roof-space gas appliance item 2.5.20 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 5.3.11 (c) and (g)—roof-space gas appliance located so that cannot be readily lit or serviced, or so that components cannot be removed creation of defective roof- space gas appliance installation—not readily lit or serviced, parts cannot be removed 2.5.21 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 5.3.11 (e)—roof-space gas appliance required to be installed in stated way on non-combustible platform or on combustible platform with compliant heat shielding was not installed that way creation of roof-space gas appliance with platform inadequately protected from combustion 2.5.22 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 5.6—thing connected to consumer piping system did not have required compliant device to allow thing to be isolated or disconnected from gas supply failure to provide required compliant way to disconnect or isolate gas supply item 2.5.23 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 5.11—gas appliance installed without required automatic gas shut-off if operation of overhead automatic fire-extinguishing equipment might extinguish appliance’s flame installation without automatic gas shut-off on automatic fire extinguishing 2.5.24 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl 5.13—gas appliance with flue made of noncompliant material or configured, located or supported in noncompliant way installation with noncompliant flue 2.5.25 fail to comply with Gas Safety Act 2000, s 8, requiring work to be done under AS 5601, cl E3.2.1—consumer piping system gas pressure dropped or gas leaked more than allowed creation of consumer piping system or connection that leaked gas or dropped gas pressure 2.5.26 fail to comply with Gas Safety Act 2000, s 9—gasfitting work completed in accordance with Gas Safety Act 2000, s 8, but certificate of compliance for work not given in accordance with Gas Safety Act 2000 failure to give appropriate certificate of compliance for pipework item 2.5.27 fail to comply with Gas Safety Act 2000, s 23 (2)—gas appliance that not approved connected to consumer piping system connection of unapproved appliance to consumer piping system Part 2.6 Plumbers licence demerit grounds for occupational item 2.6.1 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C1P4—sanitary plumbing system that does not avoid blockage or uncontrolled blockage or uncontrolled item 2.6.2 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C1P6— sanitary plumbing system that does not avoid— (a) entry of water, sewerage and sullage from the system into a building; or (b) entry of foul gases from the system into a building inconsistent with code; or (c) entry of surface water, subsurface water and storm water into the system entry of water, sewerage, sullage or foul gases into a building, or entry of outside water into the system 2.6.3 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C1P2— sanitary plumbing system that does not ensure access for maintenance of mechanical components, operational controls or for clearing blockages access for maintenance of mechanical components, operational controls or item 2.6.4 fail to comply with Water and Sewerage Regulation 2001, s 6 (1), performance requirement under plumbing code cl C1P7—sanitary plumbing system that does not avoid damage from superimposed loads, ground movement or root penetration damage from loads, ground movement or root penetration 2.6.5 fail to comply with Water and Sewerage Regulation 2001, s 18 (1), performance requirement under plumbing code cl B5P1—water service designed, constructed or installed in way that does not avoid contamination creation of water service that does not avoid contamination 2.6.6 fail to comply with Water and Sewerage Regulation 2001, s 18 (1), performance requirement under plumbing code cl B1P3—cold water service that— (a) does not ensure access for maintenance of mechanical components and operational controls; or (b) does not ensure the system, appliances and devices can be isolated for testing and maintenance creation of cold water service that does not ensure access for maintenance, or does not ensure the system, appliances and devices can be isolated for testing and maintenance item 2.6.7 fail to comply with Water and Sewerage Regulation 2001, s 18 (1), performance requirement under plumbing code cl B1P6—cold water service that does not avoid failure or uncontrolled discharge creation of cold water service that does not avoid failure or uncontrolled discharge 2.6.8 fail to comply with Water and Sewerage Act 2000, s 11 or s 15 (1) and Water and Sewerage Regulation 2001, s 17— (a) installed or fitted sprinkler system or part of fire sprinkler service without giving required notice of start to registrar; or (b) provided a water supply plumbing service without giving required notice of start to registrar or without required approval of plan of intention to start sprinkler or fire sprinkler work or give required notice of intention to start, or to get approval for plan for, water supply plumbing service 2.6.9 fail to comply with Water and Sewerage Act 2000, s 15 (2) or (3)— (a) contravened direction of registrar about how water supply plumbing service is to be provided; or (b) installed a thing to which the plumbing code, part A5 applies and the thing was not certified under the part failure to provide service as directed by registrar or installed thing not certified under plumbing code, part A5 item 2.6.10 fail to comply with Water and Sewerage Regulation 2001, s 19— (a) did not tell registrar when water supply plumbing work ready for inspection; or (b) did not leave water supply plumbing work ready for inspection as required failure to tell registrar water supply plumbing work ready for inspection or to leave work 2.6.11 fail to comply with Water and Sewerage Regulation 2001, s 20 (1)— did not test water supply plumbing in accordance with AS/NZS 3500 before it was to be passed by an inspector or, if the water supply plumbing was altered or repaired, before the alteration or repair was to be passed failure to test water supply plumbing before inspection 2.6.12 fail to comply with Water and Sewerage Regulation 2001, s 20 (3)— did not rectify water supply plumbing work found to be defective water supply plumbing work found by test item 2.6.13 fail to comply with Water and Sewerage Regulation 2001, s 21—did plan within required time for water supply plumbing work completed in accordance with the plumbing code completed water supply plumbing work 2.6.14 fail to comply with Water and Sewerage Regulation 2001, s 22 (4)— installed testable backflow prevention device but did not tell registrar about installation or ensure device tested as required as soon as practicable installation of testable backflow prevention device without notifying or testing 2.6.15 fail to comply with Water and Sewerage Act 2000, s 16—provided sanitary plumbing service without giving required notice of intention to start or complete sanitary plumbing work 2.6.16 fail to comply with Water and Sewerage Regulation 2001, s 7 (1)— did work on sanitary plumbing system other than in accordance with work other than in accordance with approved plan item 2.6.17 fail to comply with Water and Sewerage Regulation 2001, s 8— (a) did not tell registrar when sanitary plumbing work ready for inspection; or (b) did not leave sanitary plumbing work ready for inspection as failure to tell registrar sanitary plumbing work ready for inspection or to leave work 2.6.18 fail to comply with Water and Sewerage Regulation 2001, s 9 (1)— did not test sanitary plumbing in accordance with AS/NZS 3500 before it was to be passed by an inspector or, if the sanitary plumbing was altered or repaired, before the alteration or repair was to be passed failure to test sanitary plumbing before inspection 2.6.19 fail to comply with Water and Sewerage Regulation 2001, s 9 (3)— did not rectify sanitary plumbing work found to be defective sanitary plumbing work found by test item 2.6.20 fail to comply with Water and Sewerage Regulation 2001, s 10—did plan within required time for sanitary plumbing work completed in accordance with the plumbing code completed sanitary plumbing work Part 2.7 Plumbing plan certifiers licence demerit grounds for occupational discipline—Act, s 55 (1) (a) Part 2.7 Plumbing plan certifiers licence demerit grounds for item 2.7.1 fail to comply with Water and Sewerage Act 2000, s 8 (1)—approved plumbing or sanitary drainage work plan without required approvals failure to obtain required approval before approving plumbing or drainage plan 2.7.2 fail to comply with Water and Sewerage Act 2000, s 8 (2) (e)— certifier issued plan approval for proposed plumbing or sanitary drainage work, or approved amendment plan, where design of work did not comply with the plumbing code creation of plan approval or amendment for noncompliant plumbing or drainage work 2.7.3 fail to comply with Water and Sewerage Act 2000, s 9 (2)— certifier approved amendment to plan approval for proposed plumbing or sanitary drainage work if reconsideration required approved amended plan that required reconsideration Plumbing plan certifiers licence demerit grounds for occupational discipline—Act, s 55 (1) (a) Part 2.7 item 2.7.4 fail to comply with Water and Sewerage Act 2000, s 9 (4)— certifier did not keep all documents relating to approved plumbing or drainage plan for at least 12 months failure to keep plan approval records for 1 year 2.7.5 fail to comply with Water and Sewerage Act 2000, s 10—certifier did not notify registrar within 7 days after end of appointment under Water and Sewerage Act, s 5 (3) failure to notify loss of appointment as certifier within 7 days after loss Part 2.7A Works assessor licence demerit grounds for occupational discipline—Act, s 55 (1) (a) Part 2.7A Works assessor licence demerit grounds for item 2.7A.1 fail to comply with Unit Titles Act 2001, s 22B (3) (b)—fail to give copy of unit title assessment report to territory planning authority within 5 working days after giving report to applicant failure to give copy of report to authority within 5 working days after giving report to applicant All licences demerit grounds for occupational discipline—Act, s 55 (1) (a) Part 2.8 Part 2.8 All licences demerit grounds for occupational item 2.8.1 fail to comply with Act, s 40—contravention of rectification order other than emergency rectification order contravention of non- emergency rectification order 2.8.2 fail to comply with Act, s 40—contravention of emergency rectification order contravention of emergency rectification order 2.8.3 fail to comply with Act, s 47—did not give client evidence of relevant insurance before providing construction service failure to give client insurance evidence Part 2.8 All licences demerit grounds for occupational discipline—Act, s 55 (1) (a) item 2.8.4 fail to comply with Act, s 87 (1)—contravention of licence condition that— (a) limited number or cost of construction services provided under licence; or (b) required licensee to do something in a stated way in connection with the performance of a construction service failure to comply with licence condition 2.8.5 fail to comply with Act, s 87 (3)—contravention of applicable code of practice applicable code of practice Licence demerit grounds for occupational discipline under Act, s 55 (1) (other than par (a))