Commonwealth legislation

Tariff Concession Order 0615052

In ForceCTH

Jurisdiction

Commonwealth

Collection

legislative instrument

Plain English Summary

4/10 complexity

This Tariff Concession Order declares a narrowly defined polyester‑coated steel product (classified at 7210.70.00) eligible for the Schedule 4, Part III concession item 50, effective 26 September 2006 until revoked. It changes import duty treatment for that specific product. Importers and customs officers must verify the goods meet the detailed technical standards and tolerances before the concession applies, which affects import costs and compliance obligations.

JSON API

Deep dive

Want the full deep dive?

Zoe can write the in-depth analysis on top of the summary above: how it works, who it affects and what each part actually does.

Current sections

Direct links to the current provisions in Tariff Concession Order 0615052.

Tariff Concession Order 0615052

TARIFF CONCESSION ORDERUnder Section 269P of the Customs Act 1901, I, Wendy Knowles, a delegate of the Chief Executive Officer declare that the goods specified in Column 1 of THE TABLE are goods to which the item in Part III of Schedule 4 to the Customs Tariff Act 1995 specified in Column 2 of THE TABLE applies. This Order shall have effect from 26.09.06 and continue in force until revoked under sections 269SC or 269SD of the Act, or the date, if any, specified in Column 2.

THE TABLE

COLUMN 1Description of Goods including theCustoms Tariff Classification	COLUMN 2Schedule 4 Item NumberLast date of effect

7210.70.00	STEEL, high polymer polyester coated, complying with JapanIndustrial Standard G3312/SGCD1 (JIS G3312/SGCD1) AND EuropeanUnion Directive 2002/95/EC on the Restriction of the Use ofCertain Hazardous Substances in Electrical and ElectronicEquipment (RoHS), having ALL of the following:(a) epoxy reverse coating adhering to polyurethane;(b) specular gloss level NOT less than 80 units at 60 degrees;(c) distinction of image NOT less than 60 units;(d) surface having ALL of the following:(i) inclusions NOT greater than 0.2 mm over 1 squaremetre and having proximity NOT less than 400 mm;(ii) dents NOT greater than 0.3 mm over 1 square metreand having proximity NOT less than 400 mm;(iii) leveller bite NOT greater than 20 mm;(e) in ANY of the following sizes:(i) width 607 mm and gauge 0.5 mm;(ii) width 672 mm and gauge 0.5 mm;(iii) width 729 mm and gauge 0.5 mm;(iv) width 732 mm and gauge 0.5 mm;(v) width 774 mm and gauge 0.5 mm;(vi) width 824 mm and gauge 0.5 mm;(vii) width 924 mm and gauge 0.5 mm;For the purposes of this order, tolerances allowable forspecification (e) are:(a) width +2 mm;(b) gauge + or - 0.02 mmOp. 26.09.06 - TC 0615052	50

This is page 1 of 1 Page of the above Table...Wendy Knowles........................Dated 05 February 2007 Delegate of the Chief Executive Officer

Source text

Sourced from the Federal Register of Legislation (legislation.gov.au), CC BY 4.0.

1 Tariff Concession Order 0615052

THE TABLE

COLUMN 1Description of Goods including theCustoms Tariff Classification	COLUMN 2Schedule 4 Item NumberLast date of effect

7210.70.00	STEEL, high polymer polyester coated, complying with JapanIndustrial Standard G3312/SGCD1 (JIS G3312/SGCD1) AND EuropeanUnion Directive 2002/95/EC on the Restriction of the Use ofCertain Hazardous Substances in Electrical and ElectronicEquipment (RoHS), having ALL of the following:(a) epoxy reverse coating adhering to polyurethane;(b) specular gloss level NOT less than 80 units at 60 degrees;(c) distinction of image NOT less than 60 units;(d) surface having ALL of the following:(i) inclusions NOT greater than 0.2 mm over 1 squaremetre and having proximity NOT less than 400 mm;(ii) dents NOT greater than 0.3 mm over 1 square metreand having proximity NOT less than 400 mm;(iii) leveller bite NOT greater than 20 mm;(e) in ANY of the following sizes:(i) width 607 mm and gauge 0.5 mm;(ii) width 672 mm and gauge 0.5 mm;(iii) width 729 mm and gauge 0.5 mm;(iv) width 732 mm and gauge 0.5 mm;(v) width 774 mm and gauge 0.5 mm;(vi) width 824 mm and gauge 0.5 mm;(vii) width 924 mm and gauge 0.5 mm;For the purposes of this order, tolerances allowable forspecification (e) are:(a) width +2 mm;(b) gauge + or - 0.02 mmOp. 26.09.06 - TC 0615052	50

This is page 1 of 1 Page of the above Table...Wendy Knowles........................Dated 05 February 2007 Delegate of the Chief Executive Officer