Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Australian Capital Territory
Machinery Regulation 1950
SL1950-7
made under the
Machinery Act 1949
Republication No 8
Effective: 26 November 2025
Republication date: 26 November 2025
Last amendment made by A2025-29
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
About this republication
The republished law
This is a republication of the Machinery Regulation 1950, made under the Machinery Act 1949
(including any amendment made under the Legislation Act 2001, part 11.3 (Editorial changes))
as in force on 26 November 2025. It also includes any commencement, amendment, repeal or
expiry affecting this republished law to 26 November 2025.
The legislation history and amendment history of the republished law are set out in endnotes 3
and 4.
Kinds of republications
The Parliamentary Counsel’s Office prepares 2 kinds of republications of ACT laws (see the ACT
legislation register at www.legislation.act.gov.au):
• authorised republications to which the Legislation Act 2001 applies
• unauthorised republications.
The status of this republication appears on the bottom of each page.
Editorial changes
The Legislation Act 2001, part 11.3 authorises the Parliamentary Counsel to make editorial
amendments and other changes of a formal nature when preparing a law for republication.
Editorial changes do not change the effect of the law, but have effect as if they had been made by
an Act commencing on the republication date (see Legislation Act 2001, s 115 and s 117). The
changes are made if the Parliamentary Counsel considers they are desirable to bring the law into
line, or more closely into line, with current legislative drafting practice.
This republication does not include amendments made under part 11.3 (see endnote 1).
Uncommenced provisions and amendments
If a provision of the republished law has not commenced, the symbol U appears immediately
before the provision heading. Any uncommenced amendments that affect this republished law
are accessible on the ACT legislation register (www.legislation.act.gov.au). For more
information, see the home page for this law on the register.
Modifications
If a provision of the republished law is affected by a current modification, the symbol M appears
immediately before the provision heading. The text of the modifying provision appears in the
endnotes. For the legal status of modifications, see the Legislation Act 2001, section 95.
Penalties
At the republication date, the value of a penalty unit for an offence against this law is $160 for an
individual and $810 for a corporation (see Legislation Act 2001, s 133).
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
contents 1
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Australian Capital Territory
Machinery Regulation 1950
made under the
Machinery Act 1949
Contents
Page
Part 1 Preliminary
1 Name of regulation 2
2 Dictionary 2
3 Notes 2
5 Machinery to which regulation does not apply 2
6 Exemption from application of regulation 3
Part 2 Inspections
7 Authority as inspector 4
8 Power of entry 4
9 Inspector may call in aid 4
10 Occupier to allow entry and inspection 4
Contents
Page
contents 2 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Part 3 Safety provisions
12 Notice of ownership of machinery 5
13 Dangerous machinery 5
14 Traversing carriage of self-acting machinery 6
15 Risk of accident 6
16 Circular saws 11
17 Faulty or defective machinery 13
18 Appeal 14
19 Notice of accident, loss of life or injury 14
20 Notice in other cases 15
21 Reporting machinery likely to cause injury 15
22 Removing safety devices 15
Part 4 Noise
22A Meaning of ear protection device 16
22B Hearing conservation 16
22C Duty to wear ear protection devices 17
22D Defence 18
Part 5 Miscellaneous
23 Liability apart from regulation not affected 19
Dictionary 20
Endnotes
1 About the endnotes 22
2 Abbreviation key 22
3 Legislation history 23
4 Amendment history 26
5 Earlier republications 29
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 1
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Australian Capital Territory
Machinery Regulation 1950
made under the
Machinery Act 1949
Part 1 Preliminary
Section 1
page 2 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Part 1 Preliminary
1 Name of regulation
This regulation is the Machinery Regulation 1950.
2 Dictionary
The dictionary at the end of this regulation is part of this regulation.
Note 1 The dictionary at the end of this regulation defines certain terms used in
this regulation, and includes references (signpost definitions) to other
terms defined elsewhere in this regulation.
For example, the signpost definition ‘ear protection device, for part 4
(Noise)—see section 22A.’ means that the term ‘ear protection device’ is
defined in that section for part 4.
Note 2 A definition in the dictionary (including a signpost definition) applies to
the entire regulation unless the definition, or another provision of the
regulation, provides otherwise or the contrary intention otherwise appears
(see Legislation Act, s 155 and s 156 (1)).
3 Notes
A note included in this regulation is explanatory and is not part of this
regulation.
Note See the Legislation Act, s 127 (1), (4) and (5) for the legal status of notes.
5 Machinery to which regulation does not apply
This regulation does not apply to machinery—
(a) used on, or employed in the working of, the Commonwealth
Railways; or
(b) being, or forming part of, the propelling machinery of a punt,
raft, boat, ship or vessel; or
(c) being, or forming part of, the propelling machinery of a motor
vehicle, while that machinery is being used only for the
propulsion of the motor vehicle; or
Preliminary Part 1
Section 6
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 3
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(d) being, or forming part of, the propelling machinery of a traction
engine used solely for traction purposes; or
(e) being, or forming part of, a compressor freezing cabinet or an
electric drink mixer used in a retail shop; or
(f) being, or forming part of, an accounting machine or other office
appliance; or
(g) used only in or about a dwelling house for domestic purposes,
other than a circular saw.
6 Exemption from application of regulation
(1) The Minister may, in writing, exempt from the application of any
provision of this regulation any machinery or class of machinery
stated in the exemption if the Minister is satisfied that the provision
cannot reasonably be applied to that machinery or class of machinery.
(2) An exemption may be absolute or subject to the conditions stated in
the exemption.
(3) An instrument under this section is a notifiable instrument.
Part 2 Inspections
Section 7
page 4 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Part 2 Inspections
7 Authority as inspector
The Minister shall give each inspector a certificate of appointment,
and, on applying for admission to any premises or while on any
premises in the course of the inspector’s duty, an inspector must, if
required, produce the certificate to the occupier.
8 Power of entry
(1) An inspector may enter any premises and may inspect and examine
the machinery on the premises and the appliances connected with it
or belonging to it.
(2) The entry may be made at any time in the daytime, whether the
machinery is in operation or not, or at night if the machinery is then
in operation.
9 Inspector may call in aid
(1) In making the inspection the inspector may require a person
employed or working on the premises to assist the inspector, and may
require the occupier to explain the working of the machinery and to
answer questions about compliance with this regulation.
(2) A person must comply with a requirement under subsection (1).
Maximum penalty: 10 penalty units.
10 Occupier to allow entry and inspection
The occupier of premises must give an inspector all reasonable
facilities for the exercise of the inspector’s powers under this
regulation.
Safety provisions Part 3
Section 12
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 5
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Part 3 Safety provisions
12 Notice of ownership of machinery
A person who—
(a) is, at the date of the commencement of this regulation, the
occupier of premises where machinery is erected, kept or
intended to be used; or
(b) becomes the occupier of such premises after that date;
must, within 1 month after the date of commencement of this
regulation or the date when the person becomes the occupier of the
premises send to the chief inspector a written notice stating the name
of the owner, the maker’s name and the identification marks (if any)
of the machinery, the place where the machinery is erected, kept or
intended to be used, the kind of machinery, the nature and measure of
the motive power and the business or other purpose for which the
machinery is used or intended to be used.
Maximum penalty: 1 penalty unit.
13 Dangerous machinery
(1) The occupier of premises must securely fence all dangerous parts of
machinery that is in or on the premises.
(2) Without limiting subsection (1)—
(a) a hoist or teagle and flywheel directly connected with the steam
or water or other mechanical power, whether in the engine house
or not, and every part of a steam engine or other engine used for
generating mechanical power and every waterwheel must be
securely fenced; and
(b) a wheel race, not otherwise secured, must be securely fenced
close to its edge; and
Part 3 Safety provisions
Section 14
page 6 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(c) every part of the mill-gearing and every cogwheel must either
be securely fenced or be in such position or of such construction
as to be equally safe to every person employed in the premises
as it would be if it were securely fenced.
(3) All fencing must be maintained in an efficient state.
(4) The duty imposed on the occupier of premises by this section is an
absolute duty, in no way qualified by any other provision of this
regulation or another regulation made under the Act.
Maximum penalty: 10 penalty units.
14 Traversing carriage of self-acting machinery
A person must not cause or permit a traversing carriage of any self-
acting machinery to run out within a distance of 450mm from any
fixed structure, other than part of that machinery, if the space over
which it so runs out is a space over which a person is likely to pass,
whether in the course of the person’s employment or not.
Maximum penalty: 5 penalty units.
15 Risk of accident
(1) For the better prevention of accidents this section must be observed.
(2) In premises where mechanical power is used the occupier must, when
required by an inspector, provide a loose pulley or pulleys to any
machine or shafting driven by that power but an inspector must not
require a loose pulley or pulleys to be provided—
(a) for the starting of an engine, if it is equipped with self-starting
apparatus, or is directly coupled or is so constructed as to be, in
the opinion of the inspector, reasonably safe for the purpose of
starting; or
(b) if the load is connected with the driving pulley by a clutch.
Maximum penalty: 10 penalty units.
Safety provisions Part 3
Section 15
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 7
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(3) In premises where mechanical power is used, the occupier, when
directed by an inspector, must provide a belt shifter, or other safe
mechanical contrivance approved by the inspector, for the purpose of
throwing belts or pulleys on or off.
Maximum penalty: 10 penalty units.
(4) An occupier of premises, when directed by an inspector, must
provide, for the service of any shafting that is moved by mechanical
power and situated more than 2.40m above the floor level—
(a) stagings, platforms or gangways of the design and construction,
and in the position, approved by the inspector;
(b) ladders of the design and construction approved by the
inspector; and
(c) belt hangers for the purpose of holding belts not in use clear of
contact with any running machinery or mill-gearing.
Maximum penalty: 10 penalty units.
(5) A person throwing off a belt from a machine or mill-gearing must, if
a belt hanger is provided, put the belt on the belt hanger.
Maximum penalty: 10 penalty units.
(6) An occupier of premises or a person in control of a person under
16 years old must not, when any mill gearing is in motion by
mechanical power, permit the secondmentioned person to—
(a) oil or grease any part of the mill-gearing; or
(b) put on, put off, adjust, tighten or lace any belt or belting of the
mill-gearing, or attempt to do so; or
(c) go on or remain on any overhead staging erected for the purpose
of serving the mill-gearing.
Maximum penalty: 10 penalty units.
Part 3 Safety provisions
Section 15
page 8 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(7) An occupier of premises where a person under 18 years old
(the employee) is employed, or a person in control of an employee,
must not permit the employee to—
(a) be in charge of an engine; or
(b) attend to an engine, unless the attention is given under the direct
supervision of a competent person.
Maximum penalty: 10 penalty units.
(8) In a brewery or aerated water factory the occupier must—
(a) provide all bottlers, corkers, wirers, sighters and labellers with
the masks or veils, or faceguards, and the gauntlets, or
handguards or armguards, approved by an inspector; and
(b) cause all machines for bottling to be constructed and placed or
fenced to prevent as far as possible, during the operation of
filling or corking, a fragment of bursting bottle from striking any
person.
Maximum penalty: 10 penalty units.
(9) A person must, when carrying out bottling or any other operation in
the course of which explosions or breakages are likely to happen,
continually wear the faceguard or handguards or armguards provided
for the person.
Maximum penalty: 10 penalty units.
(10) An occupier of premises where machinery is operated by mechanical
power, in which a person (the employee) is employed, or a person in
charge of an employee, must not permit the employee to be employed
at or near the machinery, or in a room where the employee may pass
the machinery, while the employee is wearing flowing hair, or neck
ribbons or laces or other similar loose articles of dress.
Maximum penalty: 10 penalty units.
Safety provisions Part 3
Section 15
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 9
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(11) The occupier of premises where an emery wheel is used—
(a) must cause it to be fenced or guarded as required by an
inspector;
(b) must not permit the emery wheel to be run at a higher speed than
that indicated on it by the maker as the limit of safety; and
(c) must not permit the emery wheel to be run before a door or other
entrance.
Maximum penalty: 10 penalty units.
(12) An occupier of premises must cause all steam pipes, or pipes used for
heating purposes, to be insulated or guarded, or fixed in such a
position that a person would not come in contact with them in the
ordinary course.
Maximum penalty: 10 penalty units.
(13) An occupier of premises where are carried on operations involving
the conveyance, carrying or handling of molten metal, or of any hot
or dangerous substance must provide properly constructed and
designed pots or ladles for the purpose.
Maximum penalty: 10 penalty units.
(14) The occupier of premises where a boiler, vat or similar appliance
designed to revolve or tilt is used must cause it to be fitted with
mechanical catches or some other safe appliance to regulate its
position.
Maximum penalty: 10 penalty units.
Part 3 Safety provisions
Section 15
page 10 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(15) The occupier of premises where is used a machine worked by manual
or treadle power that is of such design and construction that its motion
is materially assisted by the kinetic energy or momentum
accumulated in its moving parts must, if an inspector directs, cause
any cogwheel, flywheel, or other moving part of the machine to be
fenced or guarded.
Maximum penalty: 10 penalty units.
(16) The occupier of premises where mechanical power is used must, if
directed by an inspector, cause all set screws, pins, keys, coupling
bolts and ends of spindles, if moved by that power, to be fenced or
guarded, or countersunk, or cut off flush with the adjoining parts of
the machinery or mill-gearing, or protected in the way the inspector
approves.
Maximum penalty: 10 penalty units.
(17) The occupier of any premises where a fan moved by mechanical
power is used must, if directed by an inspector, cause the fan to be
protected with woven wire, or fenced, or guarded in the way the
inspector approves.
Maximum penalty: 10 penalty units.
(18) The occupier of premises where machinery is moved by mechanical
power must, if required by an inspector, maintain all main traffic
ways at a width of not less than 1.20m and must keep all main traffic
ways clear of materials, stock, or other obstructions.
Maximum penalty: 10 penalty units.
(19) The occupier of premises must maintain all passageways between
machines or giving access to machines at a width of not less than
600mm.
Maximum penalty: 10 penalty units.
Safety provisions Part 3
Section 16
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 11
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(20) The occupier of premises must not—
(a) employ a person under 15 years old in working or assisting to
work any machinery; or
(b) employ a person under 18 years old, in cleaning any part of any
machinery in motion.
Maximum penalty: 10 penalty units.
16 Circular saws
(1) The occupier of premises where a circular saw is used must comply
with this section or cause those requirements to be complied with.
(2) The saw, sawbench and equipment, saw mountings and other
components of the saw installation must be designed, put together and
set up to be suitable, safe and adequately strong for the purpose for
which the saw is used or intended to be used.
(3) If the saw is part of a stationary installation, it must be erected on, and
securely fixed to, adequate foundations and must be so placed that
ample clear space for safe working is provided all round.
(4) The floor or other surface around the saw installation—
(a) must be sound, level and even; and
(b) must provide a firm foothold; and
(c) must not be allowed to become slippery; and
(d) must be kept free of stock or other impediments, and, as far as
practicable, of accumulations of sawdust and trade waste.
(5) The maximum safe working speed in revolutions per minute and the
name of the maker of the saw must be clearly and legibly impressed
on it in a conspicuous position.
Part 3 Safety provisions
Section 16
page 12 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(6) The power provided for driving the saw must be sufficient to ensure
an efficient cutting speed for all purposes for which it is used, and a
governor or other means of speed control must be provided to prevent
its being driven at a speed in excess of its maximum safe working
speed.
(7) The saw must be in good condition, the teeth sharp and correctly set
and the gullets rounded.
(8) The work of sharpening, setting and conditioning the saw must be
done in a competent way.
(9) The saw must not be used it if is cracked, fractured, warped, has teeth
missing or is otherwise defective or in bad condition.
(10) The saw must not be used unless it is maintained in good working
order and condition.
(11) The saw must be securely and truly mounted and adjusted so that it
operates without undue vibration.
(12) The saw must be provided with an efficient stopping and starting
appliance of a type that will prevent inadvertent starting, and the
control of the appliance must be in a position to enable it to be readily
and conveniently operated by the person using the saw.
(13) The saw must not be allowed to run idly between jobs, when
unattended, or when the work in hand is delayed or interrupted.
(14) The saw must be mounted, or adjusted, only while it is stopped and
secured against inadvertent starting.
(15) As far as practicable, equipment attached to the sawbench must not
be adjusted or serviced when the saw is in motion.
(16) Sawdust and trade waste must not be removed from potentially
dangerous positions under and around the saw installation when the
saw is in motion.
(17) Adequate and suitable lighting free from harmful or confusing glare
must be provided at the saw.
Safety provisions Part 3
Section 17
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 13
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(18) If an inspector is of opinion that the saw is so defective or in such
condition that its further use as a circular saw would be dangerous
and the inspector gives notice to that effect to the occupier, the saw
must immediately be rendered incapable of further use as a circular
saw.
(19) A copy of this section in good condition must be exhibited in a
conspicuous position in the premises so that it may be read by
everyone employed at or in connection with the saw and copies must
also be exhibited in other places an inspector directs.
Maximum penalty: 5 penalty units.
17 Faulty or defective machinery
(1) If machinery is, in the opinion of an inspector, so faulty or defective,
or so insufficiently guarded, or so dangerous in any other way, as to
be likely to cause loss of life or injury to any person, or if the
ventilation of a room where a steam engine or internal-combustion
engine is erected and used is, in the opinion of an inspector, defective,
the inspector may serve written notice to that effect on the occupier
of premises where the machinery or engine is erected, kept or used.
Note For how documents may be served, see the Legislation Act, pt 19.5.
(2) The notice may require the occupier to make, within a time stated in
the notice, the repairs or alterations to the machinery or its
arrangement, or to the ventilation of the room stated in the notice.
(3) A person must not refuse or fail to comply with a notice given to the
person under this section.
Maximum penalty: 10 penalty units.
(4) A person must not use, or cause to be used, any machinery or engine
the subject of the notice from a date stated in the notice until the
repairs or alterations have been effected to the satisfaction of an
inspector.
Maximum penalty: 10 penalty units.
Part 3 Safety provisions
Section 18
page 14 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
18 Appeal
(1) An occupier who is dissatisfied with the requirements of a notice
given under section 16 or section 17 may, within 21 days after the
notice has been given to the occupier, appeal to the Magistrates Court.
(2) On the hearing of the appeal the Magistrates Court may, by order,
confirm, set aside or vary the notice and may make any other order it
considers just.
(3) Until the appeal is decided by the Magistrates Court, the relevant
circular saw, machinery or engine must not be used unless the
requirements of the notice have been complied with.
19 Notice of accident, loss of life or injury
(1) If a person is killed or suffers injury by an accident caused by, or
involving, machinery, the occupier of the premises must, within 24
hours after the accident, send notice of it to the chief inspector, stating
the nature of the accident, the place where it happened, the name of
every person killed or injured and the possible extent of the damage
to the machinery.
Maximum penalty: 10 penalty units.
Note For how documents may be served, see the Legislation Act, pt 19.5.
(2) In this section:
injury means an injury that is likely to incapacitate the person injured
for more than 48 hours.
Safety provisions Part 3
Section 20
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 15
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
20 Notice in other cases
If an accident happens to machinery and the accident necessitates
structural alteration or structural repairs, the occupier of the premises
must, within 24 hours after the accident, send notice of the accident
to the chief inspector giving particulars of the accident, its cause and
the probable alterations or repairs necessitated.
Maximum penalty: 5 penalty units.
Note For how documents may be served, see the Legislation Act, pt 19.5.
21 Reporting machinery likely to cause injury
A person who is required to perform a duty at or about any machinery
must use ordinary and reasonable precautions to ascertain that the
machinery is not unsafe, and if the person finds anything likely to
cause injury to any person, the person must forthwith report it to the
manager, engineer, or other person in immediate authority over him
or her.
22 Removing safety devices
A person must not render inoperative any safety device attached to or
used for governing the speed of any engine or any safety device used
in connection with any machinery.
Maximum penalty: 10 penalty units.
Part 4 Noise
Section 22A
page 16 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Part 4 Noise
22A Meaning of ear protection device
In this part:
ear protection device means a device that complies with the
requirements of Australian Standard Specification for Hearing
Protection Devices, Australian Standard 1270.
22B Hearing conservation
(1) An occupier of premises must not require a person to perform work
in a place where—
(a) the daily noise dose to which the person is exposed exceeds
0.33; or
(b) the A weighted sound pressure level exceeds 115 decibels.
Maximum penalty: 10 penalty units.
(2) It is a defence to a prosecution for an offence against subsection (1)
for the defendant to prove that, at the time when the offence is alleged
to have been committed, everyone employed by the defendant to
work in the part of the premises in relation to which the offence is
alleged to have been committed—
(a) were provided with ear protection devices; and
(b) had been instructed in the correct use of the devices; and
(c) had been instructed to wear the devices in that part of the
premises.
(3) If the wearing of an ear protection device is reasonably likely to give
rise to a situation of danger by impairing the hearing of the wearer,
the defence provided for by subsection (2) is not available to the
occupier of the premises unless the occupier has taken reasonable
precautions to prevent injury to any person because of the creation of
such a situation of danger.
Noise Part 4
Section 22C
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 17
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
(4) For subsection (1), daily noise dose must be calculated—
(a) in accordance with the procedure set out in Australian Standard
1269-1983, section 3; and
(b) using an instrument mentioned in Australian Standard
2399-1980 as a personal noise dosimeter that complies with the
requirements of that standard.
(5) For subsection (1), the A weighted sound pressure level must be
calculated—
(a) in accordance with the procedure set out in Australian Standard
1269-1983, section 2, clause 2.6; and
(b) using an instrument mentioned in Australian Standard
1259-1982 as a Type 1, Type 2 or Type 3 sound level meter that
complies with the requirements of that standard.
(6) In this section, a reference to an Australian Standard is a reference
to the standard as in force at the time the subsection in which the
reference appears takes effect.
(7) In this section:
A weighted sound pressure level means sound pressure level
weighted in accordance with frequency weighting A.
daily noise dose—see Australian Standard 1269-1983.
frequency weighting A—see Australian Standard 1259-1982.
22C Duty to wear ear protection devices
A person who is working on premises and who has been provided by
the occupier of the premises with ear protection devices must, at all
times while machinery on the premises is in use, comply with
instructions given to the person by the occupier in connection with
the wearing of the devices.
Maximum penalty: 2 penalty units.
Part 4 Noise
Section 22D
page 18 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
22D Defence
It is a defence to a prosecution for an offence against section 22C if,
at the time the offence is alleged to have been committed, a doctor
had certified in writing that in the doctor’s opinion it was undesirable,
on medical grounds or because of physical characteristics, for the
defendant to wear the ear protection devices provided for the
defendant and the certificate had not been revoked.
Miscellaneous Part 5
Section 23
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 19
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Part 5 Miscellaneous
23 Liability apart from regulation not affected
This regulation does not operate to relieve a person from any civil or
criminal liability to which the person would be subject if this
regulation had not been made.
Dictionary
page 20 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Dictionary
(see s 2)
Note 1 The Legislation Act contains definitions and other provisions relevant to
this regulation.
Note 2 For example, the Legislation Act, dict, pt 1, defines the following terms:
• Minister (see s 162)
• notifiable instrument (see s 10)
• person (see s 160).
Note 3 Terms used in this regulation have the same meaning that they have in
the Machinery Act 1949 (see Legislation Act, s 148). For example, the
following terms are defined in the Machinery Act 1949, dict:
• chief inspector
• inspector.
ear protection device, for part 4 (Noise)—see section 22A.
engine means a piece of mechanism used to convert heat or some
other form of energy into mechanical work, or a machine for the
development or utilisation of power from some source of energy such
as coal, gas, oil, compressed air, electricity or other source.
machinery means an engine, motor or other source of motive power
other than manual, treadle, wind or animal power, and includes a
machine, shaft, belt, gearing, pulley, flywheel, contrivance or
appliance operated by any such engine, motor, or other source of
motive power, but does not include machinery that is subject to
inspection under—
(a) regulations made under the Act and relating to boilers or
engine-drivers; or
(b) other than for the Scaffolding and Lifts Act 1912, part 4
(Inspection) or the Scaffolding and Lifts Regulation 1950.
mechanical power means power other than manual or treadle power
and includes power generated by water, steam, gas, oil or electricity.
Dictionary
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 21
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
mill-gearing includes a shaft (whether upright, oblique or horizontal)
and a wheel, drum, pulley, belt, rope or chain by which the motion of
the first moving power is communicated to the operative part of a
machine.
occupier, in relation to premises, means the person in possession or
occupation, or apparently in possession or occupation, of the
premises, and includes an agent, manager, supervisor, or other person
acting or apparently acting, in the general management or control of
the premises and a person who has the general management of
machinery in those premises.
premises means—
(a) a house, building, structure, yard, mine, timber area, farm,
paddock, field, road or place; or
(b) a punt, raft, boat, ship or vessel, not propelled by its own motive
power or machinery;
where machinery is kept, worked, used or is in operation, whether the
machinery is in the premises on a permanent or temporary basis.
Endnotes
1 About the endnotes
page 22 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Endnotes
1 About the endnotes
Amending and modifying laws are annotated in the legislation history and the
amendment history. Current modifications are not included in the republished law
but are set out in the endnotes.
Not all editorial amendments made under the Legislation Act 2001, part 11.3 are
annotated in the amendment history. Full details of any amendments can be
obtained from the Parliamentary Counsel’s Office.
Uncommenced amending laws are not included in the republished law. The details
of these laws are underlined in the legislation history. Uncommenced expiries are
underlined in the legislation history and amendment history.
If all the provisions of the law have been renumbered, a table of renumbered
provisions gives details of previous and current numbering.
The endnotes also include a table of earlier republications.
2 Abbreviation key
A = Act NI = Notifiable instrument
AF = Approved form o = order
am = amended om = omitted/repealed
amdt = amendment ord = ordinance
AR = Assembly resolution orig = original
ch = chapter par = paragraph/subparagraph
CN = Commencement notice pres = present
def = definition prev = previous
DI = Disallowable instrument (prev...) = previously
dict = dictionary pt = part
disallowed = disallowed by the Legislative r = rule/subrule
Assembly reloc = relocated
div = division renum = renumbered
exp = expires/expired R[X] = Republication No
Gaz = gazette RI = reissue
hdg = heading s = section/subsection
IA = Interpretation Act 1967 sch = schedule
ins = inserted/added sdiv = subdivision
LA = Legislation Act 2001 SL = Subordinate law
LR = legislation register sub = substituted
LRA = Legislation (Republication) Act 1996 underlining = whole or part not commenced
mod = modified/modification or to be expired
Endnotes
Legislation history 3
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 23
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
3 Legislation history
This regulation was originally called the Inspection of Machinery Regulations and
was originally made under a Commonwealth ordinance—the Machinery
Ordinance 1949 No 11 (Cwlth).
The Australian Capital Territory (Self-Government) Act 1988 (Cwlth), s 34 (4)
converted most former Commonwealth ordinances in force in the ACT, and the
regulations made under them, into ACT enactments. This allowed the ACT
Legislative Assembly to amend and repeal the laws. The Machinery
Ordinance 1949 and the Inspection of Machinery Regulations were converted into
ACT enactments on 11 May 1989 (self-government day).
As with most ordinances in force in the ACT, the name was changed from
Ordinance to Act by the Self-Government (Citation of Laws) Act 1989 A1989-21,
s 5 on 11 May 1989 (self-government day).
This regulation was renamed by the Statutory Offices (Miscellaneous Provisions)
Act 1994, sch and under the Legislation Act 2001.
Before 12 September 2001, regulations commenced on their notification day unless
otherwise stated (see Interpretation Act 1967 s 50, Subordinate Laws Act 1989 s 6).
Legislation before becoming Territory enactment
Machinery Regulation 1950 SL1950-7
notified 30 November 1950
commenced 15 January 1951 (s 2 and Cwlth Gaz 1950 p 3256)
as amended by
Inspection of Machinery Regulations SL1969-1
notified 8 May 1969
commenced 8 May 1969
Amendments of the Inspection of Machinery Regulations SL1974-23
notified 22 October 1974
commenced 22 October 1974
Amendments of the Inspection of Machinery Regulations SL1975-21
notified 30 September 1975
commenced 1 December 1975
Endnotes
3 Legislation history
page 24 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Regulations to repeal certain Regulations and to revise certain
Regulations in force under the Ordinances of the Australian Capital
Territory SL1980-3 (as am by SL1980-14)
notified 25 March 1980
commenced 25 March 1980
Regulations to amend Regulations 1980 No 3 SL1980-14
notified 9 October 1980
commenced 25 March 1980
Note This regulation (SL1980-14) only amends SL1980-3.
Magistrates Court Ordinance 1985 Ord1985-67 sch pt 2
notified 19 December 1985
commenced 1 February 1986 (s 2 and Cwlth Gaz 1986 No G3)
Inspection of Machinery Regulations (Amendment) SL1986-5
notified 12 June 1986
commenced 12 June 1986
Inspection of Machinery Regulations (Amendment) SL1986-8
notified 31 July 1986
commenced 31 July 1986
Legislation after becoming Territory enactment
Statutory Offices (Miscellaneous Provisions) Act 1994 A1994-97 sch
pt 2
notified 15 December 1994 (Gaz 1994 No S280)
s 1, s 2 commenced 15 December 1994 (s 2 (1))
sch pt 2 commenced 15 December 1994 (s 2 (2) and Gaz 1994
No S293)
Regulations Revision (Penalties) Regulations SL1996-8
notified 6 June 1996 (Gaz 1996 No S108)
commenced 6 June 1996 (s 2)
Criminal Code (Theft, Fraud, Bribery and Related Offences)
Amendment Act 2004 A2004-15 sch 2 pt 2.54
notified LR 26 March 2004
s 1, s 2 commenced 26 March 2004 (LA s 75 (1))
sch 2 pt 2.54 commenced 9 April 2004 (s 2 (1))
Endnotes
Legislation history 3
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Statute Law Amendment Act 2007 A2007-3 sch 3 pt 3.65
notified LR 22 March 2007
s 1, s 2 taken to have commenced 1 July 2006 (LA s 75 (2))
sch 3 pt 3.65 commenced 12 April 2007 (s 2 (1))
Statute Law Amendment Act 2025 A2025-29 sch 3 pt 3.59, sch 4
pt 4.121
notified LR 6 November 2025
s 1, s 2 commenced 6 November 2025 (LA s 75 (1))
sch 3 pt 3.59, sch 4 pt 4.121 commenced 26 November 2025 (s 2 (3),
(9))
Endnotes
4 Amendment history
page 26 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
4 Amendment history
Name of regulation
s 1 sub A1994-97 sch pt 2
am R4 LA; R6 LA
Dictionary
s 2 om A2001-44 amdt 1.2743
ins A2007-3 amdt 3.362
Notes
s 3 om SL1975-21
ins A2007-3 amdt 3.362
Definitions for regulation
s 4 am SL1975-21; SL1986-5
defs reloc to dict A2007-3 amdt 3.361
om A2007-3 amdt 3.362
def chief inspector sub A1994-97 sch pt 2
om A2007-3 amdt 3.360
def inspector sub A1994-97 sch pt 2
om A2007-3 amdt 3.360
def the Act om A2001-44 amdt 1.2744
Machinery to which regulation does not apply
s 5 hdg sub A2025-29 amdt 3.199
s 5 am A2025-29 amdt 3.200
Exemption from application of regulation
s 6 am A2001-44 amdts 1.2745–1.2747; A2025-29 amdt 4.122
Authority as inspector
s 7 am SL1980-3; SL1996-8 sch; A2004-15 amdt 2.117,
amdt 2.118
Inspector may call in aid
s 9 am SL1996-8 sch
Obstructing inspector
s 11 am SL1996-8 sch
om A2004-15 amdt 2.118
Notice of ownership of machinery
s 12 am SL1996-8 sch
Dangerous machinery
s 13 am SL1980-3; SL1996-8 sch
Traversing carriage of self-acting machinery
s 14 am SL1974-23; SL1996-8 sch
Endnotes
Amendment history 4
R8
26/11/25
Machinery Regulation 1950
Effective: 26/11/25
page 27
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Risk of accident
s 15 am SL1974-23; SL1980-3 (as am by SL1980-14); SL1986-8;
SL1996-8 sch
Circular saws
s 16 am SL1980-3; SL1996-8 sch
Faulty or defective machinery
s 17 am SL1980-3; SL1996-8 sch; A2007-3 amdt 3.363
Appeal
s 18 sub SL1975-21
am Ord1985-67
Notice of accident, loss of life or injury
s 19 am 1980 No. 3 (as am by SL1980-14); SL1996-8 sch; A2007-3
amdt 3.363
Notice in other cases
s 20 am SL1980-3; SL1996-8 sch; A2007-3 amdt 3.363
Removing safety devices
s 22 am 1980 No. 3; SL1996-8 sch
Noise
pt 3A hdg renum as pt 4 hdg
Noise
pt 4 hdg orig pt 4 hdg
renum as pt 5 hdg
pres pt 4 hdg
(prev pt 3A hdg) ins SL1975-21
renum as pt 4 hdg A2007-3 amdt 3.364
Meaning of ear protection device
s 22A ins SL1975-21
Hearing conservation
s 22B ins SL1975-21
am SL1980-3 (as am by SL1980-14); SL1986-5; SL1996-8 sch
Duty to wear ear protection devices
s 22C ins SL1975-21
am SL1996-8 sch
Defence
s 22D ins SL1975-21
Miscellaneous
pt 5 hdg (prev pt 4 hdg) renum as pt 5 hdg A2007-3 amdt 3.364
Liability apart from regulation not affected
s 23 am SL1969-1
Endnotes
4 Amendment history
page 28 Machinery Regulation 1950
Effective: 26/11/25
R8
26/11/25
Authorised by the ACT Parliamentary Counsel—also accessible at www.legislation.act.gov.au
Service of notices etc
s 24 om A2007-3 amdt 3.365
Offences
s 25 am SL1980-3
om SL1996-8 sch
Dictionary
dict ins A2007-3 amdt 3.366
am A2025-29 amdt 3.201
def ear protection device ins A2007-3 amdt 3.366
def engine reloc from s 4 A2007-3 amdt 3.361
def machinery reloc from s 4 A2007-3 amdt 3.361
def mechanical power reloc from s 4 A2007-3 amdt 3.361
def mill-gearing reloc from s 4 A2007-3 amdt 3.361
def occupier reloc from s 4 A2007-3 amdt 3.361
def premises reloc from s 4 A2007-3 amdt 3.361