CTHIn ForceLegislation
AD/BELL 407/9 Amdt 3 - Tailboom Skin
//
© 2026 Zoe. All rights reserved.
Zoe is a legal information platform. Always consult the Federal Register of Legislation for authoritative text.
AD/BELL 407/9 Amdt 3 - Tailboom Skin
Start here
Turn the raw legal text into a practical explanation grounded in AD/BELL 407/9 Amdt 3 - Tailboom Skin.
| AD/BELL 407/9 Amdt 3 | Tailboom Skin | 4/2008 DM |
|---|
| Applicability: | Model 407 helicopters with tailbooms part number 407-030-801-107 and407-530-014-101/-103 installed. |
|---|---|
| Requirement: | Part I - Verificationa. Verify whether tailboom part number 407-030-801-107 or 407-530-014-101/-103 is installed on the helicopter.b. Enter in the helicopter technical records the appropriate tailboom part number as identified above.c. If the tailboom identified is not affected by this Directive, annotate the helicopter technical records accordingly.Part II - Surface preparation and initial inspectionPrepare the tailboom surface for “Daily Visual Check” in accordance with Part II, paragraph (1), items (a) to (e) of BHTC Alert Service Bulletin (ASB) 407-07-80 original issue, or later Transport Canada approved revision.Inspect both areas for cracks (indicated as “Daily check area” on Figure 2 in ASB 407-07-80) using a 10x magnifying glass.If a crack is detected, before further flight, replace the tailboom.If no cracking is detected, ensure both surfaces are dry and protect each reworked area with a thin coat of clear coating in accordance with applicable paragraph of Part II, of ASB 407-07-80 original issue, or later Transport Canada approved revision.Part III - Daily Visual InspectionPerform a visual check of the tailboom in accordance with Part III, paragraphs (1) and (2) of ASB 407-07-80 original issue, or later Transport Canada approved revision.If, as a result of the Part III Daily Visual Check inspection, a crack is detected, before further flight, replace the tailboom with a serviceable part. Continue this inspection if the replacement tailboom is identified in the applicability section of this Directive. |
| Part IV - 100 hour InspectionPerform a 100-hours inspection of the tailboom in accordance with Part IV of ASB 407-07-80 original issue, or later Transport Canada approved revision.If, as a result of the Part IV 100-hour inspection, a crack is detected, before further flight, replace the tailboom with a serviceable part. Continue this inspection if the replacement tailboom is identified in the applicability section of this Directive.Part V - Terminating actionReplacement of the affected tailboom with part number 407-030-801-201/-203/-205, or later part numbers, constitutes terminating action to this Directive.Note: Transport Canada AD CF-2008-04 refers. | |
|---|---|
| Compliance: | For Part I:Within 10 flight hours after 15 February 2008.For Part II:Within 25 flight hours or 30 days after 15 February 2008, whichever occurs first.For Part III:Before the first flight of the day, during the pre-flight check.For Part IV:Within 100 flight hours after 15 February 2008, and thereafter at intervals not to exceed 100 flight hours. |
| This Amendment becomes effective on 15 February 2008. | |
| Background: | There have been several reports of cracks to the tailboom skin on the left side in the area of the horizontal stabiliser. The cracks were found by normal visual inspection.Amendment 1 limited the applicability to those helicopters equipped with certain part number tailbooms. BHTC introduced a new tailboom with a chemically milled skin which is not subject to the inspections required by this Directive.Amendment 2 introduced modifications to some of the existing tailbooms, a life limitation of 5,000 hours, and a new inspection interval of 150 hours. |
| Amendment 3 is issued in response to a new Transport Canada AD, which mandates new inspection requirements introduced by ASB 407-07-80. |
|---|
Image unavailable in extracted text
David Villiers
Delegate of the Civil Aviation Safety Authority
13 February 2008