Commonwealth legislation

AD/BEECH 1900/37 - Elevator Balance Weight Attachment

In ForceCTH

Jurisdiction

Commonwealth

Collection

legislative instrument

Plain English Summary

3/10 complexity

This directive requires operators of specified Beechcraft 1900, 1900C and 1900D aeroplanes (serials listed in Raytheon MSB SB 27-3187 Rev 1) to check whether elevators were removed; if so, inspect balance-weight attachment screws and, if incorrect, replace the bolts and rebalance the elevator before further flight. It also forbids installing a rebalanced elevator unless fitted with drilled-head NAS6703HU12–NAS6703HU22 bolts secured with safety wire. Initial logbook/inspection actions must occur within 200 flight hours of 20 February 2003.

JSON API

Deep dive

Want the full deep dive?

Zoe can write the in-depth analysis on top of the summary above: how it works, who it affects and what each part actually does.

Current sections

Direct links to the current provisions in AD/BEECH 1900/37 - Elevator Balance Weight Attachment.

AIRWORTHINESS DIRECTIVE

View image in the official source

AIRWORTHINESS DIRECTIVE

For the reasons set out in the background section, the CASA delegate whose signature appears below issues the following Airworthiness Directive (AD) under subregulation 39.1 (1) of CAR 1998. The AD requires that the action set out in the requirement section (being action that the delegate considers necessary to correct the unsafe condition) be taken in relation to the aircraft or aeronautical product mentioned in the applicability section: (a) in the circumstances mentioned in the requirement section; and (b) in accordance with the instructions set out in the requirement section; and (c) at the time mentioned in the compliance section.

View image in the official source

Beechcraft 1900 Series Aeroplanes

AD/BEECH 1900/37 Elevator Balance Weight

AD/BEECH 1900/37 Elevator Balance Weight Attachment 2/2003

Applicability: Models 1900, 1900C, and 1900D aircraft, with serial numbers listed in Raytheon Mandatory Service Bulletin (MSB) SB 27-3187, Revision 1, Revised September 2001.

Requirement: 1. Check the aircraft logbook to determine whether the elevator(s) have been removed. If, by checking the logbook, it can be positively determined that the elevators have never been removed, no further action is required.

2. If, by checking the logbook, it can determined that the elevator(s) has/have been removed, or if complete records of elevator(s) do not exist, inspect the elevator balance weight attachment screws to determine if they are the correct length in accordance with the Accomplishment Instructions section of Raytheon MSB SB 27-3187 Revision 1. If the inspection reveals the elevator balance weight attachment screws are the correct length, no further action is required.

3. If, during the Requirement 2 inspection, the elevator balance weight attachment screw(s) are found to be incorrect length, remove and rebalance the elevator(s) by installing the balance weights with the appropriate new elevator balance weight attachment bolts in accordance with the Accomplishment Instructions section of Raytheon MSB SB 27-3187 Revision 1, and the applicable maintenance manual.

4. Do not install, on any affected aircraft, an elevator that has been rebalanced unless it has been rebalanced by installing the balance weights with the appropriate new balance weight attachment bolts, part number in the range of NAS6703HU12 through NAS6703HU22, that have drilled heads and are secured with safety wire.

Note: FAA AD 2002-23-11 Amdt 39-12955 refers.

Compliance: For Requirements 1 and 2: Within 200 hours time in service after 20 February 2003.

Requirement 3: Before further flight. Requirement 4: As of 20 February 2003.

This Airworthiness Directive becomes effective on 20 February 2003.

Source text

Sourced from the Federal Register of Legislation (legislation.gov.au), CC BY 4.0.

AIRWORTHINESS DIRECTIVE AIRWORTHINESS DIRECTIVE

AIRWORTHINESS DIRECTIVE

Beechcraft 1900 Series Aeroplanes

AD/BEECH 1900/37 Elevator Balance Weight AD/BEECH 1900/37 Elevator Balance Weight Attachment 2/2003

AD/BEECH 1900/37 Elevator Balance Weight Attachment 2/2003

Applicability: Models 1900, 1900C, and 1900D aircraft, with serial numbers listed in Raytheon Mandatory Service Bulletin (MSB) SB 27-3187, Revision 1, Revised September 2001.

2. If, by checking the logbook, it can determined that the elevator(s) has/have been removed, or if complete records of elevator(s) do not exist, inspect the elevator balance weight attachment screws to determine if they are the correct length in accordance with the Accomplishment Instructions section of Raytheon MSB SB 27-3187 Revision 1. If the inspection reveals the elevator balance weight attachment screws are the correct length, no further action is required.

3. If, during the Requirement 2 inspection, the elevator balance weight attachment screw(s) are found to be incorrect length, remove and rebalance the elevator(s) by installing the balance weights with the appropriate new elevator balance weight attachment bolts in accordance with the Accomplishment Instructions section of Raytheon MSB SB 27-3187 Revision 1, and the applicable maintenance manual.

4. Do not install, on any affected aircraft, an elevator that has been rebalanced unless it has been rebalanced by installing the balance weights with the appropriate new balance weight attachment bolts, part number in the range of NAS6703HU12 through NAS6703HU22, that have drilled heads and are secured with safety wire.

Note: FAA AD 2002-23-11 Amdt 39-12955 refers.