8 The cure for compressed air illness is immediate and adequate
recompression, which causes diminution in the size and final
disappearance of the bubble of gas that produced the symptom.
(see s 2)
Note 1 The Legislation Act contains definitions and other provisions relevant to
this regulation.
Note 2 For example, the Legislation Act, dict, pt 1, defines the following terms:
• document
• person.
Note 3 Terms used in this regulation have the same meaning that they have in
the Scaffolding and Lifts Act 1912 (see Legislation Act, s 148). For
example, the following terms are defined in the Scaffolding and Lifts Act
1912, dict:
• crane
• dogger
• gear
• inspector
• lift
• plant.
analogous means radically analogous in relation to prime
characteristics.
approved means approved in writing by the chief inspector.
axial stress means one produced by a force or load acting parallel to
and concentrically with the longitudinal neutral axis of the member
concerned, and is the initial stress so produced, before any
redistribution that may accompany resultant elastic deformation of
the member.
bearing pressure, in relation to a pin or shaft in a plain bearing, means
bearing pressure calculated as for a plane rectangular area of length
equal to the length of the bearing, and of width equal to the diameter
of the bearing.
birdcage scaffolding—see section 85.
cantilever scaffolding—see section 85.
conveyor, for part 4 (Lifts)—see section 16.
dead loads means all loads of which the principal effects remain
constant during operation or manipulation of the crane, lift, hoist,
scaffolding, plant or gear concerned.
designed means effectively and correctly designed for its purpose in
complete accordance with this regulation or, if provision is not
included in this regulation, effectively and correctly designed for its
purpose in an approved way.
drawings means permanent, fully detailed and fully dimensioned and
annotated engineering drawings, clear, distinct, and to a commonly
used scale, which are sufficiently complete for engineering workshop
use to enable faithful manufacture of all items depicted.
dynamically irreversible means incapable of being set or kept in
motion by energy applied at or to the power output member or part of
any mechanism, linkage or device.
dynamically reversible means capable of being set or kept in motion
by energy applied at or to the power output member or part of any
mechanism, linkage or device.
explosive-powered tool, for part 9A (Explosive-powered tools—
safety measures)—see section 118A.
fixed end means for purposes of stress determination, a fixed end or
fixed connection so designed that it effectively maintains and
preserves the tangent to the elastic curve of the end of the member
concerned in its original direction and position, irrespective of
applied loading.
forged steel means hot forged from steel conforming to Australian
Standard Specification No E17—(1944 T.) General Locomotive
Forgings of K quality, and Australian Standard Specification
No B63—1938 Carbon Steel Forgings (Primarily for Cranes and
Hoists).
free end means for purposes of stress determination, a free end not
specifically secured in a way that will effectively prevent its
translation.
heavy duty scaffolding—see section 85.
high tensile structural steel means steel conforming to British
Standard Specification No 548—1934, High Tensile Structural Steel
for Bridges etc and General Building Construction, or British
Standard Specification No 968—1941, High Tensile (Fusion Welding
Quality) Steel for Bridges, etc, and General Building Construction
promulgated by Standards Australia.
hinged end means for purposes of stress determination, a hinged end
or hinged connection not specifically and effectively designed to
transmit major restraining or other moments.
in commission means in commission but not necessarily active.
independent pole scaffolding—see section 85.
light duty scaffolding—see section 85.
light swinging stage—see section 85.
limiting means—
(a) a maximum such that if it were increased; or
(b) a minimum such that if it were decreased;
the increase or decrease would occasion contravention of the Act or
this regulation, or in any way prejudice the safe working of the crane,
lift, hoist, scaffolding or plant concerned.
live loads means all loads of which the principal effects vary during
operation or manipulation of the crane, lift, hoist, scaffolding, plant
or gear concerned, and include the working load and all loads due to
inertia, momentum, braking and wind.
mild steel means—
(a) except in relation to bolts or rivets—mild steel conforming to
Australian Standard Specification No A.1—1940 Rolled Steel
Sections for Structural Purposes; and
(b) in relation to bolts or rivets—a mild steel approved by the chief
inspector as being suitable for its purpose.
projectile, for part 9A (Explosive-powered tools—safety
measures)—see section 118A.
qualified operator, for part 9A (Explosive-powered tools—safety
measures)—see section 118A.
roller means a wheel or cylinder that is either without an axle, or in
which an axle or equivalent device is employed principally for
purposes of alignment and location as distinct from the transmission
of loads or forces.
run—see section 85.
S.A.A. Wiring Rules means Australian Standard Rules for the
electrical equipment of buildings, structures and premises, published
by the Standards Australia, known as the S.A.A. Wiring Rules. (First
issued June, 1931, revised December, 1934, revised January, 1940.
Reprinted including corrigenda of February, 1940, February, 1943,
and March, 1944. Amendment 3, 1945. All redated 1945.
Amendment 4, January, 1946, redated 1946.).
safety gear, for part 4 (Lifts)—see section 16.
safe working load (or working load) means the greatest burden that
may be imposed without contravening any provision of this
regulation in or on the lifting or lowering instrument with which any
crane, lift or hoist is provided for lifting or lowering, or on any
platform of any scaffold, but does not include wind loads or any
increase consequential to section 125 or the weight of the lifting hook,
yoke, kibble, box, cage, vessel or other medium by which the load is
raised or lowered, or the weight of the platform or framework of any
scaffold.
second-hand means evidencing previous usage that might reasonably
be expected or anticipated to have resulted in wear or abrasion,
distortion, fatigue, misalignment, cold working, strain hardening,
overheating, corrosion, or other damage or deterioration, affecting the
item concerned in whole or in part, and, in relation to any material,
second-hand means not plainly self evidently new.
section means actual section before any deformation that may follow
or accompany application of stress and, unless otherwise stated, all
sections must lie in planes normal to the longitudinal axes of the
members concerned.
service lift, for part 4 (Lifts)—see section 16.
single pole scaffolding—see section 85.
static counterbalance weights includes all counterbalance weights
that do not move relatively to the crane, hoist, lift, scaffolding, plant
or gear concerned or to its supporting structure.
strength means computed strength except in relation to the strengths
of materials or ropes, and unless the chief inspector specifically
approves otherwise.
stress means stress measured in tons per square inch, after including
all increases prescribed by this regulation.
suspended scaffolding—see section 85.
toe board—see section 85.
tool, for part 9A (Explosive-powered tools—safety measures)—see
section 118A.
transverse stress means the longitudinal tensile or compressive fibre
stress resulting at the skin of a member from forces that cause flexure,
but not include the axial stress.
under power means energised by any agency other than manual or
gravitational.
use, an explosive-powered tool, for part 9A (Explosive-powered
tools—safety measures)—see section 118A (3).
work, for part 9A (Explosive-powered tools—safety measures)—see
section 118A.
working load—see safe working load.
1 About the endnotes
1 About the endnotes
Amending and modifying laws are annotated in the legislation history and the
amendment history. Current modifications are not included in the republished law
but are set out in the endnotes.
Not all editorial amendments made under the Legislation Act 2001, part 11.3 are
annotated in the amendment history. Full details of any amendments can be
obtained from the Parliamentary Counsel’s Office.
Uncommenced amending laws and expiries are listed in the legislation history and
the amendment history. These details are underlined. Uncommenced provisions
and amendments are not included in the republished law but are set out in the last
endnote.
If all the provisions of the law have been renumbered, a table of renumbered
provisions gives details of previous and current numbering.
The endnotes also include a table of earlier republications.
2 Abbreviation key
am = amended ord = ordinance
amdt = amendment orig = original
ch = chapter par = paragraph/subparagraph
def = definition pres = present
dict = dictionary prev = previous
disallowed = disallowed by the Legislative (prev...) = previously
Assembly pt = part
div = division r = rule/subrule
exp = expires/expired renum = renumbered
Gaz = gazette reloc = relocated
hdg = heading R[X] = Republication No
IA = Interpretation Act 1967 RI = reissue
ins = inserted/added s = section/subsection
LA = Legislation Act 2001 sch = schedule
LR = legislation register sdiv = subdivision
LRA = Legislation (Republication) Act 1996 sub = substituted
mod = modified/modification SL = Subordinate Law
o = order underlining = whole or part not commenced
om = omitted/repealed or to be expired
Legislation history 3
This regulation was originally a NSW regulation—the Regulations made under the
Scaffolding and Lifts Act 1912 (NSW).
The Scaffolding and Lifts Act 1912 (NSW) and this regulation were applied, in a
modified form, as ACT laws by the Scaffolding and Lifts Act 1957 (now repealed).
This regulation was renamed by the Scaffolding and Lifts Regulations Amendment
SL1999-19 and later under the Legislation Act 2001.
Under the Interpretation Act 1967 (repealed), s 65 all former NSW Acts in force in
the ACT immediately before 10 November 1999 (including the Scaffolding and
Lifts Act 1912) became, for all purposes, laws made by the ACT Legislative
Assembly.
Under the Scaffolding and Lifts Act 1912, s 28 (now expired) the Scaffolding and
Lifts Regulation 1950 became, on 29 March 2001, for all purposes, a regulation
made under that Act. This completed the process of making the regulation fully into
an ACT law.
Before 11 May 1989, regulations commenced on their notification day unless
otherwise stated (see Interpretation Act 1967 s 50).
Before 11 May 1989, ordinances commenced on their notification day unless
otherwise stated (see Seat of Government (Administration) Act 1910 (Cwlth), s 12).
NSW legislation
notified 25 May 1950 (NSW Gaz 1950 No 86)
commenced 1 June 1950 (s 1 (1))
as amended by
notified 1 September 1950 (NSW Gaz 1950 No 141)
commenced 1 September 1950
notified 3 November 1950 (NSW Gaz 1950 No 168)
commenced 3 November 1950
notified 6 March 1953 (NSW Gaz 1953 No 44)
commenced 6 March 1953
notified 3 December 1954 (NSW Gaz 1954 No 197)
commenced 3 December 1954
notified 5 August 1955 (NSW Gaz 1955 No 76)
commenced 5 August 1955
notified 9 March 1956 (NSW Gaz 1956 No 24)
commenced 9 March 1956
notified 22 June 1956 (NSW Gaz 1956 No 69)
commenced 22 June 1956
notified 19 October 1956 (NSW Gaz 1956 No 113)
commenced 19 October 1956
notified 1 March 1957 (NSW Gaz 1957 No 29)
commenced 1 March 1957
Commonwealth legislation
Scaffolding and Lifts Act 1957 A1957-8 sch pt 2 (as am by Ord1968-5;
Ord1974-26; Ord1976-7; Ord1977-28; Ord1981-15; Ord1982-15;
Ord1982-68; Ord1983-34)
notified 19 September 1957 (Cwlth Gaz 1957 No 51)
commenced 19 September 1957
Legislation history 3
Scaffolding and Lifts Ordinance 1968 Ord1968-5
notified 21 March 1968 (Cwlth Gaz 1968 No 26)
commenced 21 March 1968
Scaffolding and Lifts Ordinance 1974 Ord1974-26
notified 30 July 1974 (Cwlth Gaz 1974 No 62)
commenced 30 July 1974
Scaffolding and Lifts Ordinance 1976 Ord1976-7
notified 24 February 1976 (Cwlth Gaz 1976 No S38)
commenced 24 February 1976
Scaffolding and Lifts (Amendment) Ordinance 1977 Ord1977-28
notified 1 July 1977 (Cwlth Gaz 1977 No S124)
commenced 1 July 1977
Scaffolding and Lifts (Amendment) Ordinance 1981 Ord1981-15
notified 30 June 1981 (Cwlth Gaz 1981 No S128)
commenced 30 June 1981
Scaffolding and Lifts (Amendment) Ordinance 1982 Ord1982-15
notified 7 May 1982 (Cwlth Gaz 1982 No S93)
commenced 7 May 1982
Scaffolding and Lifts (Amendment) Ordinance (No 2) 1982
Ord1982-68
notified 18 August 1982 (Cwlth Gaz 1982 No S174)
commenced 18 August 1982
Scaffolding and Lifts (Amendment) Ordinance 1983 Ord1983-34
notified 29 September 1983 (Cwlth Gaz 1983 No S226)
commenced 1 October 1983 (s 2)
Regulations under the Scaffolding and Lifts Act, 1912 of the State of
New South Wales in their application to the Territory (Amendment)
SL1986-9
notified 31 July 1986 (Cwlth Gaz 1986 No S375)
commenced 31 July 1986
Self-Government (Consequential Amendments) Ordinance 1989
Ord1989-38 sch 2
notified 10 May 1989 (Cwlth Gaz 1989 No S160)
s 1, s 2 commenced 10 May 1989 (s 2 (1))
sch 2 commenced 11 May 1989 (s 2 (2) and see Cwlth Gaz 1989
No S164)
Legislation after becoming Territory enactment
Scaffolding and Lifts Regulations Amendment SL1999-19
notified 30 September 1999 (Gaz 1999 No S57)
commenced 30 September 1999 (s 1)
Occupational Health and Safety Legislation Regulations Amendment
SL2000-47 pt 3
notified 30 November 2000 (Gaz 2000 No 48)
commenced 30 November 2000 (s 1)
Statute Law Amendment Act 2001 A2001-11 sch 3
notified 29 March 2001 (Gaz 2001 No 13)
commenced 29 March 2001 (s 2)
Legislation (Consequential Amendments) Act 2001 A2001-44 pt 359
notified 26 July 2001 (Gaz 2001 No 30)
s 1, s 2 commenced 26 July 2001 (IA s 10B)
pt 359 commenced 12 September 2001 (s 2 and see Gaz 2001
No S65)
Statute Law Amendment Act 2007 A2007-3 sch 3 pt 3.92
notified LR 22 March 2007
s 1, s 2 taken to have commenced 1 July 2006 (LA s 75 (2))
sch 3 pt 3.92 commenced 12 April 2007 (s 2 (1))
Work Safety Legislation Amendment Act 2009 A2009-28 sch 2 pt 2.11
notified LR 9 September 2009
s 1, s 2 commenced 9 September 2009 (LA s 75 (1))
sch 2 pt 2.11 commenced 1 October 2009 (s 2 and see Work Safety
Act 2008 A2008-51, s 2 (1) (b) and CN2009-11)
Name of regulation
s 1 am regs gazetted 9 March 1956; regs gazetted 22 June 1956
om A1957-8 sch pt 2 (as am Ord1977-28 s 5)
ins SL1999-19 sch
am R2 LA
s 2 om A1957-8 sch pt 2 (as am Ord1977-28 s 4)
ins A2007-3 amdt 3.471
Notes
s 3 defs reloc to dict A2007-3 amdt 3.470
sub A2007-3 amdt 3.471
def chief inspector ins A1957-8 sch pt 2
om A2007-3 amdt 3.469
def inspector ins A1957-8 sch pt 2
om A2007-3 amdt 3.469
def the Act sub A1957-8 sch pt 2; A2001-11 amdt 3.257
om A2001-44 amdt 1.3879
def the Explosives Act 1905 ins A1957-8 sch pt 2
om SL1999-19 sch
s 8 sub regs gazetted 1 September 1950
s 9 om regs gazetted 1 September 1950
s 10 sub regs gazetted 1 September 1950
s 11 sub A1957-8 sch pt 2
s 12 om A1957-8 sch pt 2
pt 3 hdg om A1957-8 sch pt 2
s 15 om A1957-8 sch pt 2
Interpretation
div 4.1 hdg ins R2 LA
Design, construction and erection of lifts
div 4.2 hdg (prev pt 4 div A hdg) renum R2 LA
s 17 am A1957-8 sch pt 2; regs renum R2 LA
s 18 ss renum R2 LA
s 22 ss renum R2 LA
s 23 ss renum R2 LA
s 24 ss renum R2 LA
s 25 sub regs gazetted 3 December 1954
ss renum R2 LA
s 27 ss renum R2 LA
s 28 ss renum R2 LA
s 29 ss renum R2 LA; ss renum R3 LA
s 31 ss renum R2 LA
s 32 ss renum R2 LA
s 33 ss renum R2 LA
s 35 am A1957-8 sch pt 2; A2001-11 amdt 3.258
s 39 ss renum R2 LA
s 40 ss renum R2 LA
s 41 ss renum R2 LA
s 46 ss renum R2 LA
s 51 ss renum R2 LA
s 56 ss renum R2 LA
s 61 ss renum R2 LA
s 62 ss renum R2 LA
s 63 ss renum R2 LA
Maintenance of lifts
div 4.3 hdg (prev pt 4 div B hdg) renum R2 LA
s 67 pars renum R2 LA
Use of lifts
div 4.4 hdg (prev pt 4 div C hdg) renum R2 LA
s 68 am SL2000-47 s 11; ss etc renum R2 LA
s 69 am A1957-8 sch pt 2
s 70 am SL2000-47 s 12
s 72A ins regs gazetted 22 June 1956
sub A1957-8 sch pt 2 (as am Ord1974-26 s 2; Ord1977-28
s 5)
am A1957-8 sch pt 2 (as am Ord1981-15 s 2; Ord1982-68 s 2)
om A1957-8 sch pt 2 (as am Ord1983-34) s 5)
div 5.1 hdg (prev pt 5 div A hdg) renum R2 LA
s 73 am A1957-8 sch pt 2 (as am Ord1976-7 s 2); ss etc renum R2
LA
s 75 ss renum R2 LA
s 76 om regs gazetted 22 June 1956
Construction, erecting, adding to, altering, repairing, finishing, painting and
div 5.2 hdg (prev pt 5 div B hdg) renum R2 LA
s 78 ss renum R2 LA
s 79 ss renum R2 LA
s 80 ss renum R2 LA
s 81 ss renum R2 LA
s 82 am A1957-8 sch pt 2; A2001-11 amdt 3.259; ss etc renum R2
LA
s 83 am A1957-8 sch pt 2; ss etc renum R2 LA
Demolition of buildings and structures
div 5.3 hdg (prev pt 5 div C hdg) renum R2 LA
s 84 am regs gazetted 22 June 1956; SL1999-19 sch; ss etc renum
R2 LA; A2009-28 amdt 2.27
s 86 ss etc renum R2 LA
s 87 am regs gazetted 3 December 1954; ss etc renum R2 LA
s 88 ss renum R2 LA
s 89 ss etc renum R2 LA
s 90 ss renum R2 LA
s 91 ss etc renum R2 LA
s 92 ss etc renum R2 LA
s 93 ss etc renum R2 LA
s 94 ss renum R2 LA
div 7.1 hdg (prev pt 7 div A hdg) renum R2 LA
s 95 am regs gazetted 3 December 1954; regs gazetted 22 June
1956; ss renum R2 LA
Cofferdams and caissons
div 7.2 hdg (prev pt 7 div B hdg) renum R2 LA
Trenches
div 7.3 hdg (prev pt 7 div C hdg) renum R2 LA
s 97 ss renum R2 LA
Shafts, wells and tunnels
div 7.4 hdg (prev pt 7 div D hdg) renum R2 LA
s 98 ss renum R2 LA
Diving
div 8.1 hdg (prev pt 8 div A hdg) renum R2 LA
s 99 am regs gazetted 22 June 1956; A1957-8 sch pt 2; SL1999-19
sch; ss etc renum R2 LA
Tunnelling
div 8.2 hdg (prev pt 8 div B hdg) renum R2 LA
s 100 am regs gazetted 22 June 1956; A1957-8 sch pt 2; SL1986-9
s 3; SL1999-19 sch; ss etc renum R2 LA
Caissons
div 8.3 hdg renum R2 LA
s 101 am regs gazetted 22 June 1956; A1957-8 sch pt 2; SL1986-9;
SL1999-19 s 2 sch; ss etc renum R2 LA
pt 9 hdg om SL1999-19 sch
s 102 om SL1999-19 sch
s 103 am A1957-8 sch pt 2
om SL1999-19 sch
s 104 om SL1999-19 sch
s 105 om SL1999-19 sch
s 106 om SL1999-19 sch
s 107 om SL1999-19 sch
s 108 om SL1999-19 sch
s 109 om SL1999-19 sch
s 110 om SL1999-19 sch
s 111 om SL1999-19 sch
s 112 om SL1999-19 sch
s 113 om SL1999-19 sch
s 114 om SL1999-19 sch
s 115 om SL1999-19 sch
s 116 om SL1999-19 sch
s 117 om SL1999-19 sch
s 118 om SL1999-19 sch
Explosive-powered tools—safety measures
pt 9A hdg sub A2007-3 amdt 3.472
s 118A ins regs gazetted 9 March 1956
s 118B ins regs gazetted 9 March 1956; ss etc renum R2 LA
s 118C ins regs gazetted 9 March 1956; ss renum R2 LA
s 118D ins regs gazetted 9 March 1956; ss etc renum R2 LA
s 118E ins regs gazetted 9 March 1956; ss etc renum R2 LA
s 118F ins regs gazetted 9 March 1956; ss renum R2 LA
s 118G ins regs gazetted 9 March 1956; ss renum R2 LA
s 118H ins regs gazetted 9 March 1956
First-aid equipment
div 10.1 hdg (prev pt 10 div A hdg) renum R2 LA
s 119 am regs gazetted 3 December 1954; ss renum R2 LA
Shelter, change and dining accommodation
div 10.2 hdg (prev pt 10 div B hdg) renum R2 LA
s 120 ss etc renum R2 LA
Sanitary conveniences and washing facilities
div 10.3 hdg (prev pt 10 div C hdg) renum R2 LA
s 121 am A1957-8 sch pt 2 (as am Ord1968-5 s 2); SL1986-9 s 4; ss
etc renum R2 LA
s 122 am A1957-8 sch pt 2; ss etc renum R2 LA
s 123 ss renum R2 LA
s 124 ss renum R2 LA
s 125 ss renum R2 LA
s 126 ss etc renum R2 LA
s 127 am regs gazetted 5 August 1955; A2001-11 amdt 3.260; ss etc
renum R2 LA
s 128 ss renum R2 LA
s 129 ss renum R2 LA
s 130 am regs gazetted 3 December 1954; ss renum R2 LA
s 131 ss renum R2 LA
s 132 am regs gazetted 5 August 1955; ss etc renum R2 LA
s 132A ins regs gazetted 1 March 1957; ss renum R2 LA
s 133 ss renum R2 LA
s 134 ss renum R2 LA
s 135 ss renum R2 LA
s 136 ss renum R2 LA
s 137 ss renum R2 LA
s 138 am SL2000-47 s 13; ss renum R2 LA
s 139 ss etc renum R2 LA
s 140 ss renum R2 LA
s 141 ss renum R2 LA
s 142 ss etc renum R2 LA
s 143 am A1957-8 sch pt 2; A2001-11 amdt 3.261; ss etc renum R2
LA
s 144 am regs gazetted 19 October 1956; A2001-11 amdt 3.262; ss
etc renum R2 LA
s 145 ss etc renum R2 LA
s 150 pars renum R2 LA
s 151 ss renum R2 LA
s 154 pars etc renum R2 LA
s 156 ss etc renum R2 LA
s 157 ss renum R2 LA
s 158 ss etc renum R2 LA
pt 14 hdg om SL2000-47 s 14
s 159 am regs gazetted 3 December 1954; A1957-8 sch pt 2 (as am
Ord1976-7 s 3; Ord1977-28 s 5; Ord1983-34) s 5)
s 160 am regs gazetted 3 December 1954; A1957-8 sch pt 2
s 161 am regs gazetted 3 December 1954; A1957-8 sch pt 2
pt 15 hdg om SL2000-47 s 14
s 162 am regs gazetted 3 December 1954; A1957-8 sch pt 2 (as am
Ord1977-28 s 5; Ord1983-34) s 5)
s 163 om A1957-8 sch pt 2 (as am Ord1983-34) s 5)
s 164 am A1957-8 sch pt 2 (as am Ord1977-28 s 4); ss renum R2
LA
sch 1 am regs gazetted 3 November 1950; regs gazetted 6 March
1953; regs gazetted 22 June 1956; A1957-8 sch pt 2 (as am
Ord1976-7 s 2; Ord1977-28 s 5; Ord1982-15 s 2;
Ord1982-68 s 2)
om A1957-8 sch pt 2 (as am Ord1983-34) s 5)
sch 2 am regs gazetted 22 June 1956; regs gazetted 19 October
Method of treatment of silica paint for the purpose of ascertaining the
percentage of free silica present
sch 3 hdg (prev third sch hdg) renum R2 LA
sch 3 items renum R2 LA
Processes to which regulation 73 (1) (o) applies
sch 4 hdg (prev fourth sch hdg) renum R2 LA
Method of treatment of a lead compound for the purpose of determining the
percentage of dry compound of lead
sch 5 hdg (prev fifth sch hdg) renum R2 LA
sch 5 items renum R2 LA
sch 6 om SL1999-19 sch
sch 7 hdg (prev seventh sch hdg) renum R2 LA
Medical standards and examination report for compressed air workers
sch 8 hdg (prev eighth sch hdg) renum R2 LA
sch 8 pars renum R2 LA
Symptoms and treatment of compressed air illness
sch 9 hdg (prev ninth sch hdg) renum R2 LA
sch 9 cl etc renum R2 LA
dict ins A2007-3 amdt 3.473
def analogous reloc from s 3 A2007-3 amdt 3.470
def approved reloc from s 3 A2007-3 amdt 3.470
def axial stress reloc from s 3 A2007-3 amdt 3.470
def bearing pressure reloc from s 3 A2007-3 amdt 3.470
def birdcage scaffolding ins A2007-3 amdt 3.473
def cantilever scaffolding ins A2007-3 amdt 3.473
def conveyor ins A2007-3 amdt 3.473
def dead loads reloc from s 3 A2007-3 amdt 3.470
def designed reloc from s 3 A2007-3 amdt 3.470
def drawings reloc from s 3 A2007-3 amdt 3.470
def dynamically irreversible reloc from s 3 A2007-3
def dynamically reversible reloc from s 3 A2007-3
def explosive-powered tool ins A2007-3 amdt 3.473
def fixed end reloc from s 3 A2007-3 amdt 3.470
def forged steel reloc from s 3 A2007-3 amdt 3.470
def free end reloc from s 3 A2007-3 amdt 3.470
def heavy duty scaffolding ins A2007-3 amdt 3.473
def high tensile structural steelreloc from s 3 A2007-3
def hinged end reloc from s 3 A2007-3 amdt 3.470
def in commission reloc from s 3 A2007-3 amdt 3.470
def independent pole scaffolding ins A2007-3 amdt 3.473
def light duty scaffolding ins A2007-3 amdt 3.473
def light swinging stage ins A2007-3 amdt 3.473
def limiting reloc from s 3 A2007-3 amdt 3.470
def live loads reloc from s 3 A2007-3 amdt 3.470
def mild steel reloc from s 3 A2007-3 amdt 3.470
def projectile ins A2007-3 amdt 3.473
def qualified operator ins A2007-3 amdt 3.473
def roller reloc from s 3 A2007-3 amdt 3.470
def run ins A2007-3 amdt 3.473
def S.A.A. Wiring Rules reloc from s 3 A2007-3 amdt 3.470
def safety gear ins A2007-3 amdt 3.473
def safe working load (or working load) reloc from s 3
A2007-3 amdt 3.470
def second-hand reloc from s 3 A2007-3 amdt 3.470
def section reloc from s 3 A2007-3 amdt 3.470
def service lift ins A2007-3 amdt 3.473
def single pole scaffolding ins A2007-3 amdt 3.473
def static counterbalance weights reloc from s 3 A2007-3
def strength reloc from s 3 A2007-3 amdt 3.470
def stress reloc from s 3 A2007-3 amdt 3.470
def suspended scaffolding ins A2007-3 amdt 3.473
def toe board ins A2007-3 amdt 3.473
def tool ins A2007-3 amdt 3.473
def transverse stress reloc from s 3 A2007-3 amdt 3.470
5 Earlier republications
def under power reloc from s 3 A2007-3 amdt 3.470
def use ins A2007-3 amdt 3.473
def work ins A2007-3 amdt 3.473
def working load reloc from s 3 A2007-3 amdt 3.470
5 Earlier republications
Some earlier republications were not numbered. The number in column 1 refers to
the publication order.
Since 12 September 2001 every authorised republication has been published in
electronic pdf format on the ACT legislation register. A selection of authorised
republications have also been published in printed format. These republications are
marked with an asterisk (*) in column 1. Electronic and printed versions of an
authorised republication are identical.
Republication No Amendments to Republication date
1 SL1986-9 31 October 1993
2 A2001-44 11 September 2002
3 A2001-44 4 November 2004
4 A2007-3 12 April 2007