NATIONAL ELECTRICITY (NORTHERN TERRITORY) (NATIONAL UNIFORM LEGISLATION) (MODIFICATION) REGULATIONS 2016
106Chapter 11A inserted
Start here
Get a plain-English read of 106
Turn the raw legal text into a practical explanation grounded in NATIONAL ELECTRICITY (NORTHERN TERRITORY) (NATIONAL UNIFORM LEGISLATION) (MODIFICATION) REGULATIONS 2016.
106 Chapter 11A inserted
After Chapter 11
11A. NT Savings and Transitional Rules
Part A Savings and transitional rules for Chapter 5
11A.1 Chapter 5 provisions
(1) In this Rule:
regulatory investment test means a regulatory investment test
under Part D of Chapter 5.
(2) A Primary Transmission Network Service Provider is not required to
publish or provide information under clause 5.2A.5(a) until
Regulations 2016 273
(3) A Distribution Network Service Provider is not required to have and
publish its first information pack under clause 5.3A.3(a)(3) until
(4) A Distribution Network Service Provider is not required to include in
its first Distribution Annual Planning Report published under
clause 5.13.2 the information specified in clause S5.8(a)(5) if
information on energy and demand forecasts was not required to be
reported by the Distribution Network Service Provider under
jurisdictional electricity legislation applicable at the time the
previous report was prepared.
(5) The requirement to undertake a regulatory investment test does not
apply in relation to:
(a) a project that was assessed by the AER for the purposes of its
distribution determination for Power and Water Corporation
(ABN 15 947 352 360) for the period of 5 years commencing
on 1 July 2019; or
(b) a project where an assessment equivalent to a regulatory
investment test has been commenced by Power and Water
Corporation before 1 July 2019.
(6) A Transmission Network Service Provider is not required to comply
with clause 5.18A.3(f) until 1 July 2024 in relation to the content of
an impact assessment under that clause.
Part B Savings and transitional rules for Chapter 5A
Note
Part B of this Chapter has no effect in this jurisdiction until 1 July 2019 (see
11A.2 Model standing offers
11A.2.1 Definitions
In this Rule:
NT distributor means Power and Water Corporation ABN 15 947
352 360.
relevant provisions means Chapter 5A and Chapter 6, Part DA.
transition date means the date on which the transition period
ends.
Regulations 2016 274
transition period means the period from the commencement of the
1st regulatory control period (being 1 July 2019) to 30 June 2020.
11A.2.2 Extended meaning of some terms
During the transition period:
(a) a basic connection service includes not only a connection
service for which a model standing offer has been approved
by the AER (see paragraph (c) of the definition in
clause 5A.A.1) but also one for which the AER's approval of a
model standing offer is not required;
(b) a standard connection service includes not only a connection
service for which a model standing offer has been approved
by the AER (see the definition in clause 5A.A.1) but also one
for which the AER's approval of a model standing offer is not
required; and
(c) a model standing offer includes a document prepared and
published by the NT distributor, without the AER's approval,
as a model standing offer to have effect during the transition
period (but not beyond the end of that period).
11A.2.3 Transitional operation of relevant provisions
(a) During the transition period, the relevant provisions operate subject
to the exclusions, qualifications and modifications prescribed by this
Rule.
(b) However, the relevant provisions operate without the exclusions,
qualifications and modifications prescribed by this Rule insofar as
they relate to:
(1) a period beyond the transition period; or
(2) a person (such as a new entrant to the industry) that is not the
NT distributor.
Example
If the NT distributor submits a regulatory proposal for the regulatory control
period that follows the transition period, the distributor is bound by the relevant
provisions (without exclusion, qualification or modification) in relation to the
regulatory proposal even though the proposal is submitted during the transition
(c) A transaction commenced by or with the NT distributor during the
transition period may be continued and completed after the
transition period without regard to changes to the rules governing
the transaction that take effect at the end of the transition period.
Regulations 2016 275
11A.2.4 Exclusions, qualifications and modifications
During the transition period, the relevant provisions apply to, and in
relation to, the NT distributor subject to the following exclusions,
qualifications and modifications:
Model standing offers (basic connection services)
(a) A document, prepared by the NT distributor and published on
the NT distributor's website, will (although not approved by the
AER) be regarded as a model standing offer to provide basic
connection services during the transition period if it complies
with the requirements of clause 5A.B.2(b) as to its terms and
conditions.
(b) If, during the transition period, the AER approves a model
standing offer for the same basic connection services, the
approved model standing offer supersedes the former model
standing offer under this clause.
(c) The NT distributor's obligation to have a model standing offer
to provide basic connection services (clause 5A.B.1) operates
during the transition period but the AER's approval of the
model standing offer is not required until the transition date.
(d) The NT distributor's obligation to submit for the AER's
approval a proposed model standing offer to provide basic
connection services (clause 5A.B.2(a)) does not arise until
Model standing offer (standard connection services)
(e) A document, prepared by the NT distributor and published on
the NT distributor's website, will (although not approved by the
AER) be regarded as a model standing offer to provide
standard connection services during the transition period if it
complies with the requirements of clause 5A.B.4(c) as to its
terms and conditions.
(f) If, during the transition period, the AER approves a model
standing offer for the same standard connection services, and
the approved model standing offer is to take effect before the
end of the transition period, the approved model standing offer
supersedes the former model standing offer.
(g) The NT distributor may submit for the AER's approval a model
standing offer to provide standard connection services
(clause 5A.B.4) during the transition period but the AER's
approval of the standing offer is not required until the transition
Regulations 2016 276
Amendment of standing offers
(h) During the transition period, the NT distributor may amend a
standing offer to provide basic connection services or
standard connection services during the transition period by
publishing the amendments and the amended text on its
website. (This paragraph applies during the transition period to
the exclusion of clause 5A.B.6.)
11A.2.5 References
A reference to any of the relevant provisions in a legislative or other
instrument will be construed, during the transition period, as a
reference to the provision as modified by this Rule.
Part C Savings and transitional rules for Chapter 7A
Note
Part C of this Chapter has no effect in this jurisdiction until 1 July 2019 (see
Legislation) (Modification) Regulations). The application of Part C will be
11A.3 Existing metering installations
(a) This rule applies in relation to a metering installation installed at a
connection point on a transmission network or distribution network
in this jurisdiction that is in service immediately before 1 July 2019.
(b) The following requirements must be complied with in relation to the
(1) the requirements imposed on a metering installation at a
connection point on a distribution network or transmission
network in this jurisdiction by, under or for the purposes of a
law of this jurisdiction that is in force immediately before
1 July 2019 (the NT requirements); and
(2) the requirements imposed in respect of the metering
installation by the Rules.
(c) The requirements imposed in respect of the metering installation by
the following provisions are taken to be complied with:
(1) clause 7A.6.2(a);
(2) clause 7A.6.3(a);
(3) clause 7A.6.4, other than paragraph (b);
(4) clause 7A.6.5;
Regulations 2016 277
(5) schedule 7A.1, other than clause S7A.1.3;
(6) clause S7A.3.2.2;
(7) schedule 7A.5.
(d) For the purposes of the operation of Chapter 7A in respect of the
metering installation, a reference in:
(1) clause 7A.7.2 to "the technical requirements";
(2) clause 7A.7.3 to "requirements of the Rules";
(3) clause 7A.7.4 to "schedule 7A.1" or "relevant accuracy
requirement";
(4) clause 7A.8.7 to "schedule 7A.1";
(5) clause S7A.3.2.2(c) to "requirements of the Rules"; and
(6) Chapter 10, definition metering installation malfunction, to
"the requirements of schedule 7A.1",
must be regarded as a reference to "the NT requirements".
(e) If the metering installation is replaced on or after 1 July 2019,
paragraphs (b) to (d) no longer apply in respect of the metering
11A.4 Testing metering installations
The time periods for testing of metering installations under
Table S7A.6.1.2 do not apply to metering installations that are at
least 10 years old on 1 July 2019 until 1 July 2022.
11A.5 Metering data services database and related requirements
(1) The Metering Data Provider for this jurisdiction on 1 July 2019 is
not, on or after that date, required to comply with all the
requirements under rule 7A.8 relating to establishing and
maintaining a metering data services database but the following
requirements will apply:
(a) the Metering Data Provider must ensure that all of those
requirements under rule 7A.8 are complied with by
31 March 2025 (with the period between 1 July 2019 and
31 March 2025 being referred to as the transitional period),
including by acquiring, gaining or upgrading computing
capabilities, equipment and other assets and materials, and
establishing or enhancing processes and systems, to ensure
Regulations 2016 278
compliance;
(b) during the transitional period, the Metering Data Provider
must, insofar as is reasonably practicable, use its existing
resources and capabilities (and any upgraded, enhanced,
additional or new resources and capabilities as they become
reasonably available) to comply with those requirements
under rule 7A.8, especially in relation to the validation,
substitution and estimation of metering data in its metering
data services database; and
(c) without limiting paragraph (b), the Metering Data Provider
must use its best endeavours to:
(i) maximise the quality of metering data; and
(ii) maximise transparency in processes for verifying,
validating, calculating and estimating metering data.
(2) During the transitional period:
(a) the requirements imposed by clause S7A.7.13.5(c)(4) and (5)
will not apply in relation to the Metering Data Provider;
(b) the Metering Data Provider is only required to include
information, data and matters on its metering register in
accordance with the requirements of clause S7A.8.8.2(e)(4) to
the extent that it is reasonably able to do so; and
(c) the reference in clause S7A.8.8.2(e)(5) to a communication
guideline, in its application to the Metering Data Provider, will
be taken to be a reference to the interim communication
guideline prepared by NTESMO under rule 11A.6.
(3) In addition, during the transitional period:
(a) the Metering Provider is only required to include information,
data and matters on a register of metering installations in
accordance with the requirements of clause S7A.8.7.1(a)(1) to
the extent that it is reasonably able to do so; and
(b) the reference in clause S7A.8.7.1(a)(2) to a communication
guideline, in its application to the Metering Provider, will be
taken to be a reference to the interim communication guideline
prepared by NTESMO under rule 11A.6.
(4) For the transitional period, if information about a metering
installation is included in the metering register, then the metering
installation is to be taken, for the purposes of Chapter 7A, to be
registered with NTESMO.
Regulations 2016 279
11A.6 Communication guideline
NTESMO is not required to have a comprehensive communication
guideline in place under clause S7A.1.3 until the Metering Data
Provider is in a position to comply with its obligations under
rule 7A.8 relating to establishing and maintaining a metering data
services database, after taking into account the operation of
rule 11A.5, but the following requirements will apply:
(a) NTESMO must have an interim communication guideline in
place by 1 January 2020;
(b) the interim communication guideline must comply with the
requirements of clause S7A.1.3(c), (d) and (e) insofar as is
reasonably practicable and after taking into account the
Metering Data Provider's resources and capabilities during the
period applying under clause 11A.5(1)(a);
(c) NTESMO must maintain the interim communication guideline
until the Metering Data Provider is in a position to comply the
obligations under rule 7A.8, and may review and vary the
interim communication guideline from time to time; and
(d) NTESMO must revise or replace the interim communication
guideline so that a comprehensive communication guideline is
in place when the Metering Data Provider is in a position to
comply with its obligations under rule 7A.8.
11A.7 Timeframes for meters to be installed
(1) In this rule:
commencement date means 1 July 2019.
maintenance replacement means the replacement of a retail
customer's existing meter arranged by a retailer that is based on
the results of sample testing of a meter population carried out in
accordance with Chapter 7A:
(a) which indicates that it is necessary or appropriate, in
accordance with good electricity industry practice, for the
meter to be replaced to ensure compliance with Chapter 7A;
and
(b) details of which have been provided to the retailer under
Chapter 7A, together with the results of the sample testing that
support the need for the replacement.
Regulations 2016 280
new meter deployment means the replacement of an existing
meter of one or more retail customers which is arranged by a
retailer other than where the replacement is:
(a) at the request of the relevant retail customer or to enable the
provision of a product or service the retail customer has
agreed to acquire from the retailer or any other person;
(b) a maintenance replacement; or
(c) as a result of a metering installation malfunction.
(2) This rule applies where, before the commencement date, a retailer
has an outstanding request for a meter to be installed, including in
relation to a new connection, at a retail customer's premises and
that request does not relate to a new meter deployment or a
metering installation malfunction (an existing metering
installation request).
(3) On and from the commencement date, Chapter 7A will apply to an
existing metering installation request as if:
(a) the timeframe for the meter to be installed for the purposes of
clause 7A.6.10(a)(2) ends at the later of:
(i) 6 business days from the date the retailer is informed
that the connection service (as defined in clause 5A.A.1)
is complete; and
(ii) 6 business days from the commencement date;
(b) for the purposes of clause 7A.6.11(a)(2), the retailer received
the request from the retail customer on the commencement
date; and
(c) for the purposes of clause 7A.6.12(a)(1)(ii) and (d), the retailer
received the request from the retail customer on the
commencement date.