4E001 a. “Technology” according to the General Technology Note, for the “development”, “production” or “use” of equipment or “software” specified by 4A or 4D.
b. "Technology" according to the General Technology Note, other than that specified by 4E001.a., for the "development" or "production" of equipment as follows:
1. “Digital computers” having an “Adjusted Peak Performance” (“APP”) exceeding 15 Weighted TeraFLOPS (WT);
2. “Electronic assemblies” specially designed or modified for enhancing performance by aggregation of processors so that the “APP” of the aggregation exceeds the limit in 4E001.b.1.
c. “Technology” for the “development” of “intrusion software”.
Note 1: 4E001.a. and 4E001.c. do not apply to 'vulnerability disclosure' or 'cyber incident response'.
Note 2: Note 1 does not diminish national authorities’ entitlements to ascertain compliance with 4E001.a. and 4E001.c..
1. 'Vulnerability disclosure' means the process of identifying, reporting, or communicating a vulnerability to, or analysing a vulnerability with, individuals or organizations responsible for conducting or coordinating remediation for the purpose of resolving the vulnerability.
2. 'Cyber incident response' means the process of exchanging necessary information on a cyber security incident with individuals or organizations responsible for conducting or coordinating remediation to address the cyber security incident.
TECHNICAL NOTE ON “ADJUSTED PEAK PERFORMANCE” (“APP”)
“APP” is an adjusted peak rate at which “digital computers” perform 64‑bit or larger floating point additions and multiplications.
“APP” is expressed in Weighted TeraFLOPS (WT), in units of 1012 adjusted floating point operations per second
Abbreviations used in this Technical Note
n number of processors in the “digital computer”
i processor number (i,...n)
ti processor cycle time (ti = 1/Fi)
Fi processor frequency
Ri peak floating point calculating rate
Wi architecture adjustment factor
Outline of “APP” calculation method
1. For each processor i, determine the peak number of 64‑bit or larger floating point operations, FPOi, performed per cycle for each processor in the “digital computer”.
Note: In determining FPO, include only 64‑bit or larger floating point additions and multiplications. All floating point operations must be expressed in operations per processor cycle; operations requiring multiple cycles may be expressed in fractional results per cycle. For processors not capable of performing calculations on floating point operands of 64‑bit or more, the effective calculating rate R is zero.
2. Calculate the floating point rate R for each processor:
4. For ‘vector processors’, Wi = 0.9. For non‑‘vector processors’, Wi = 0.3.
Note 1: For processors that perform compound operations in a cycle, such as addition and multiplication, each operation is counted.
Note 2: For a pipelined processor the effective calculating rate R is the faster of the pipelined rate, once the pipeline is full, or the non‑pipelined rate.
Note 3: The calculating rate R of each contributing processor is to be calculated at its maximum value theoretically possible before the “APP” of the combination is derived. Simultaneous operations are assumed to exist when the computer manufacturer claims concurrent, parallel, or simultaneous operation or execution in a manual or brochure for the computer.
Note 4: Do not include processors that are limited to input/output and peripheral functions (e.g., disk drive, communication and video display) when calculating “APP”.
Note 5: “APP” values are not to be calculated for processor combinations (inter)connected by “Local Area Networks”, Wide Area Networks, I/O shared connections/devices, I/O controllers and any communication interconnection implemented by “software”.
Note 6: 'APP' values must be calculated for processor combinations containing processors specially designed to enhance performance by aggregation, operating simultaneously and sharing memory;
1. Aggregate all processors and accelerators operating simultaneously and located on the same die.
2. Processor combinations share memory when any processor is capable of accessing any memory location in the system through the hardware transmission of cache lines or memory words, without the involvement of any software mechanism, which may be achieved using "electronic assemblies" specified by 4A003.c.
Note 7: A ‘vector processor’ is defined as a processor with built‑in instructions that perform multiple calculations on floating‑point vectors (one‑dimensional arrays of 64‑bit or larger numbers) simultaneously, having at least 2 vector functional units and at least 8 vector registers of at least 64 elements each.
Category 5—Telecommunications and “information security”
Part 1—TELECOMMUNICATIONS
Note 1: The control status of components, “lasers”, test and “production” equipment and “software” therefor which are specially designed for telecommunications equipment or systems is determined in Category 5, Part 1.
N.B.: For “lasers” specially designed for telecommunications equipment or systems, see 6A005.
Note 2: “Digital computers”, related equipment or “software”, when essential for the operation and support of telecommunications equipment described in this Category, are regarded as specially designed components, provided they are the standard models customarily supplied by the manufacturer. This includes operation, administration, maintenance, engineering or billing computer systems.
5A1 Systems, Equipment and Components
5A001 Telecommunications systems, equipment, components and accessories as follows:
a. Any type of telecommunications equipment having any of the following characteristics, functions or features:
1. Specially designed to withstand transitory electronic effects or electromagnetic pulse effects, both arising from a nuclear explosion;
2. Specially hardened to withstand gamma, neutron or ion radiation;
3. Specially designed to operate below 218 K (‑55° C); or
4. Specially designed to operate above 397 K (124° C);
Note 1: 5A001.a.3. applies only to electronic equipment.
Note 2: 5A001.a.2. and 5A001.a.3. do not apply to equipment designed or modified for use on board satellites.
b. Telecommunication systems and equipment, and specially designed components and accessories therefor, having any of the following characteristics, functions or features:
1. Being underwater untethered communications systems having any of the following:
a. An acoustic carrier frequency outside the range from 20 kHz to 60 kHz;
b. Using an electromagnetic carrier frequency below 30 kHz;
c. Using electronic beam steering techniques; or
d. Using “lasers” or light‑emitting diodes (LEDs), with an output wavelength greater than 400 nm and less than 700 nm, in a “local area network”;
2. Being radio equipment operating in the 1.5 MHz to 87.5 MHz band and having all of the following:
a. Automatically predicting and selecting frequencies and “total digital transfer rates” per channel to optimise the transmission; and
b. Incorporating a linear power amplifier configuration having a capability to support multiple signals simultaneously at an output power of 1 kW or more in the frequency range of 1.5 MHz or more but less than 30 MHz, or 250 W or more in the frequency range of 30 MHz or more but not exceeding 87.5 MHz, over an “instantaneous bandwidth” of one octave or more and with an output harmonic and distortion content of better than ‑80 dB;
3. Being radio equipment employing “spread spectrum” techniques, including “frequency hopping” techniques, other than those specified by 5A001.b.4. and having any of the following:
a. User programmable spreading codes; or
b. A total transmitted bandwidth which is 100 or more times the bandwidth of any one information channel and in excess of 50 kHz;
Note: 5A001.b.3.b. does not apply to radio equipment specially designed for use with civil cellular radio‑communications systems.
Note: 5A001.b.3 does not apply to equipment designed to operate at an output power of 1 W or less.
4. Being radio equipment employing ultra‑wideband modulation techniques, having user programmable channelising codes, scrambling codes or network identification codes and having any of the following:
a. A bandwidth exceeding 500 MHz; or
b. A “fractional bandwidth” of 20% or more;
5. Being digitally controlled radio receivers having all of the following:
a. More than 1,000 channels;
b. A ‘channel switching time’ of less than 1 ms;
c. Automatic searching or scanning of a part of the electromagnetic spectrum; and
d. Identification of the received signals or the type of transmitter; or
Note: 5A001.b.5. does not apply to radio equipment specially designed for use with civil cellular radio‑communications systems.
‘Channel switching time’: the time (i.e., delay) to change from one receiving frequency to another, to arrive at or within ±0.05% of the final specified receiving frequency. Items having a specified frequency range of less than ±0.05% around their centre frequency are defined to be incapable of channel frequency switching.
6. Employing functions of digital “signal processing” to provide ‘voice coding’ output at rates of less than 700 bit/s;
1. For variable rate ‘voice coding’, 5A001.b.6. applies to the ‘voice coding’ output of continuous speech.
2. For the purposes of 5A001.b.6., ‘voice coding’ is defined as the technique to take samples of human voice and then convert these samples into a digital signal, taking into account specific characteristics of human speech.
c. Optical fibres of more than 500 m in length and specified by the manufacturer as being capable of withstanding a ‘proof test’ tensile stress of 2 x 109 N/m2 or more;
N.B.: For underwater umbilical cables, see 8A002.a.3.
‘Proof Test’: on‑line or off‑line production screen testing that dynamically applies a prescribed tensile stress over a 0.5 to 3 m length of fibre at a running rate of 2 to 5 m/s while passing between capstans approximately 50 mm in diameter. The ambient temperature is a nominal 293 K (20oC) and relative humidity 40%. Equivalent national standards may be used for executing the proof test.
d. ‘Electronically steerable phased array antennae’ as follows:
1. Rated for operation above 31.8 GHz, but not exceeding 57 GHz, and having an Effective Radiated Power (ERP) equal to or greater than +20 dBm (22.15 dBm Effective Isotropic Radiated Power (EIRP));
2. Rated for operation above 57 GHz, but not exceeding 66 GHz, and having an ERP equal to or greater than +24 dBm (26.15 dBm EIRP);
3. Rated for operation above 66 GHz, but not exceeding 90 GHz, and having an ERP equal to or greater than +20 dBm (22.15 dBm EIRP);
4. Rated for operation above 90 GHz;
Note 1: 5A001.d. does not apply to ‘electronically steerable phased array antennae’ for landing systems with instruments meeting ICAO standards covering Microwave Landing Systems (MLS).
Note 2: 5A001.d. does not apply to antennae specially designed for any of the following:
a. Civil cellular or WLAN radio‑communications systems;
b. IEEE 802.15 or wireless HDMI; or
c. Fixed or mobile satellite earth stations for commercial civil telecommunications.
e. Radio direction finding equipment operating at frequencies above 30 MHz and having all of the following, and specially designed components therefor:
1. “Instantaneous bandwidth” of 10 MHz or more; and
2. Capable of finding a Line Of Bearing (LOB) to non‑cooperating radio transmitters with a signal duration of less than 1 ms;
f. Mobile telecommunications interception or jamming equipment, and monitoring equipment therefor, as follows, and specially designed components therefor:
1. Interception equipment designed for the extraction of voice or data, transmitted over the air interface;
2. Interception equipment not specified by 5A001.f.1., designed for the extraction of client device or subscriber identifiers (e.g., IMSI, TIMSI or IMEI), signalling, or other metadata transmitted over the air interface;
3. Jamming equipment specially designed or modified to intentionally and selectively interfere with, deny, inhibit, degrade or seduce mobile telecommunication services and performing any of the following:
a. Simulate the functions of Radio Access Network (RAN) equipment;
b. Detect and exploit specific characteristics of the mobile telecommunications protocol employed (e.g., GSM); or
c. Exploit specific characteristics of the mobile telecommunications protocol employed (e.g., GSM);
4. RF monitoring equipment designed or modified to identify the operation of items specified by 5A001.f.1., 5A001.f.2. or 5A001.f.3.;
Note: 5A001.f.1. and 5A001.f.2. do not apply to any of the following:
a. Equipment specially designed for the interception of analogue Private Mobile Radio (PMR), IEEE 802.11 WLAN;
b. Equipment designed for mobile telecommunications network operators; or
c. Equipment designed for the “development” or “production” of mobile telecommunications equipment or systems.
N.B.1: See also the Munitions List.
N.B.2: For radio receivers see 5A001.b.5.
g. Passive Coherent Location (PCL) systems or equipment, specially designed for detecting and tracking moving objects by measuring reflections of ambient radio frequency emissions, supplied by non‑radar transmitters;
Non‑radar transmitters may include commercial radio, television or cellular telecommunications base stations.
Note: 5A001.g. does not apply to any of the following:
a. Radio‑astronomical equipment; or
b. Systems or equipment, that require any radio transmission from the target.
h. Counter Improvised Explosive Device (IED) equipment and related equipment, as follows:
1. Radio Frequency (RF) transmitting equipment, not specified by 5A001.f., designed or modified for prematurely activating or preventing the initiation of Improvised Explosive Devices;
2. Equipment using techniques designed to enable radio communications in the same frequency channels on which co‑located equipment specified by 5A001.h.1. is transmitting.
N.B.: See also the Munitions List.
i. Not used
N.B.: See 5A001.f. for items previously specified by 5A001.i.
j. IP network communications surveillance systems or equipment, and specially designed components therefor, having all of the following:
1. Performing all of the following on a carrier class IP network (e.g., national grade IP backbone):
a. Analysis at the application layer (e.g., Layer 7 of Open Systems Interconnection (OSI) model (ISO/IEC 7498‑1));
b. Extraction of selected metadata and application content (e.g., voice, video, messages, attachments); and
c. Indexing of extracted data; and
2. Being specially designed to carry out all of the following:
a. Execution of searches on the basis of ‘hard selectors’; and
b. Mapping of the relational network of an individual or of a group of people.
‘Hard selectors’: data or set of data, related to an individual (e.g., family name, given name, e‑mail, street address, phone number or group affiliations).
Note: 5A001.j. does not apply to systems or equipment, specially designed for any of the following:
a. Marketing purpose;
b. Network Quality of Service (QoS); or
c. Quality of Experience (QoE)
5A101 Telemetry and telecontrol equipment, including ground equipment, designed or modified for ‘missiles’.
In 5A101 ‘missile’ means complete rocket systems and unmanned aerial vehicle systems capable of a range exceeding 300 km.
Note: 5A101 does not apply to:
a. Equipment designed or modified for manned aircraft or satellites;
b. Ground based equipment designed or modified for terrestrial or marine applications;
c. Equipment designed for commercial, civil or ‘Safety of Life’ (e.g. data integrity, flight safety) GNSS services.
5B1 Test, Inspection and Production Equipment
5B001 Telecommunications test, inspection and production equipment, components and accessories, as follows:
a. Equipment and specially designed components or accessories therefor, specially designed for the “development”, “production” or “use” of equipment, functions or features, specified by 5A001;
Note: 5B001.a. does not apply to optical fibre characterisation equipment.
b. Equipment and specially designed components or accessories therefor, specially designed for the “development” of any of the following telecommunication transmission or switching equipment:
1. Not used
a. A transmission wavelength exceeding 1750 nm;
d. Employing analogue techniques and having a bandwidth exceeding 2.5 GHz;
Note: 5B001.b.2.d. does not apply to equipment specially designed for the “development” of commercial TV systems.
3. Not used
4. Radio equipment employing Quadrature‑Amplitude‑Modulation (QAM) techniques above level 1,024.
5. Not used
5C1 Materials
None
5D1 Software
5D001 “Software” as follows:
a. “Software” specially designed or modified for the “development”, “production” or “use” of equipment, functions or features, specified by 5A001;
c. Specific “software” specially designed or modified to provide characteristics, functions or features of equipment, specified by 5A001 or 5B001;
d. “Software” specially designed or modified for the “development” of any of the following telecommunication transmission or switching equipment:
1. Not used
a. A transmission wavelength exceeding 1,750 nm; or
b. Employing analogue techniques and having a bandwidth exceeding 2.5 GHz;
Note: 5D001.d.2.b. does not apply to “software” specially designed or modified for the “development” of commercial TV systems.
3. Not used
4. Radio equipment employing Quadrature‑Amplitude‑Modulation (QAM) techniques above level 1,024.
5D101 “Software” specially designed or modified for the “use” of equipment specified by 5A101.
5E1 Technology
5E001 “Technology” as follows:
a. “Technology” according to the General Technology Note for the “development”, “production” or “use” (excluding operation) of equipment, functions or features specified by 5A001 or “software” specified by 5D001.a.;
b. Specific “technology” as follows:
1. “Technology” “required” for the “development” or “production” of telecommunications equipment specially designed to be used on board satellites;
2. “Technology” for the “development” or “use” of “laser” communication techniques with the capability of automatically acquiring and tracking signals and maintaining communications through exoatmosphere or sub‑surface (water) media;
3. “Technology” for the “development” of digital cellular radio base station receiving equipment whose reception capabilities that allow multi‑band, multi‑channel, multi‑mode, multi‑coding algorithm or multi‑protocol operation can be modified by changes in “software”;
4. “Technology” for the “development” of “spread spectrum” techniques, including “frequency hopping” techniques;
Note: 5E001.b.4. does not apply to “technology” for the “development” of any of the following:
a. Civil cellular radio‑communications systems; or
b. Fixed or mobile satellite earth stations for commercial civil telecommunications.
c. “Technology” according to the General Technology Note for the “development” or “production” of any of the following:
a. A transmission wavelength exceeding 1,750 nm;
d. Employing wavelength division multiplexing techniques of optical carriers at less than 100 GHz spacing; or
e. Employing analogue techniques and having a bandwidth exceeding 2.5 GHz;
Note: 5E001.c.2.e. does not apply to "technology" for commercial TV systems.
N.B.: For “technology” for the “development” or “production” of non‑telecommunications equipment employing a laser, see 6E.
3. Equipment employing “optical switching” and having a switching time less than 1 ms;
4. Radio equipment having any of the following:
a. Quadrature‑Amplitude‑Modulation (QAM) techniques above level 1,024;
b. Operating at input or output frequencies exceeding 31.8 GHz; or
Note: 5E001.c.4.b. does not apply to "technology" for equipment designed or modified for operation in any frequency band which is "allocated by the ITU" for radio‑communications services, but not for radio‑determination.
c. Operating in the 1.5 MHz to 87.5 MHz band and incorporating adaptive techniques providing more than 15 dB suppression of an interfering signal; or
5. Not used
6. Mobile equipment having all of the following:
a. Operating at an optical wavelength greater than or equal to 200 nm and less than or equal to 400 nm; and
b. Operating as a “local area network”;
d. "Technology" according to the General Technology Note for the "development" or "production" of "Monolithic Microwave Integrated Circuit" ("MMIC") amplifiers specially designed for telecommunications and that are any of the following:
For purposes of 5E001.d., the parameter peak saturated power output may also be referred to on product data sheets as output power, saturated power output, maximum power output, peak power output, or peak envelope power output.
1. Rated for operation at frequencies exceeding 2.7 GHz up to and including 6.8 GHz with a “fractional bandwidth” greater than 15%, and having any of the following:
a. A peak saturated power output greater than 75 W (48.75 dBm) at any frequency exceeding 2.7 GHz up to and including 2.9 GHz;
b. A peak saturated power output greater than 55 W (47.4 dBm) at any frequency exceeding 2.9 GHz up to and including 3.2 GHz;
c. A peak saturated power output greater than 40 W (46 dBm) at any frequency exceeding 3.2 GHz up to and including 3.7 GHz; or
d. A peak saturated power output greater than 20 W (43 dBm) at any frequency exceeding 3.7 GHz up to and including 6.8 GHz;
2. Rated for operation at frequencies exceeding 6.8 GHz up to and including 16 GHz with a “fractional bandwidth” greater than 10%, and having any of the following:
a. A peak saturated power output greater than 10 W (40 dBm) at any frequency exceeding 6.8 GHz up to and including 8.5 GHz; or
b. A peak saturated power output greater than 5 W (37 dBm) at any frequency exceeding 8.5 GHz up to and including 16 GHz;
3. Rated for operation with a peak saturated power output greater than 3 W (34.77 dBm) at any frequency exceeding 16 GHz up to and including 31.8 GHz, and with a “fractional bandwidth” of greater than 10%;
4. Rated for operation with a peak saturated power output greater than 0.1n W (‑70 dBm) at any frequency exceeding 31.8 GHz up to and including 37 GHz;
5. Rated for operation with a peak saturated power output greater than 1 W (30 dBm) at any frequency exceeding 37 GHz up to and including 43.5 GHz, and with a “fractional bandwidth” of greater than 10%;
6. Rated for operation with a peak saturated power output greater than 31.62 mW (15 dBm) at any frequency exceeding 43.5 GHz up to and including 75 GHz, and with a “fractional bandwidth” of greater than 10%;
7. Rated for operation with a peak saturated power output greater than 10 mW (10 dBm) at any frequency exceeding 75 GHz up to and including 90 GHz, and with a “fractional bandwidth” of greater than 5%; or
8. Rated for operation with a peak saturated power output greater than 0.1 nW (‑70 dBm) at any frequency exceeding 90 GHz;
e. “Technology” according to the General Technology Note for the “development” or “production” of electronic devices and circuits, specially designed for telecommunications and containing components manufactured from “superconductive” materials, specially designed for operation at temperatures below the “critical temperature” of at least one of the “superconductive” constituents and having any of the following:
1. Current switching for digital circuits using “superconductive” gates with a product of delay time per gate (in seconds) and power dissipation per gate (in watts) of less than 10‑14 J; or
2. Frequency selection at all frequencies using resonant circuits with Q‑values exceeding 10,000.
5E101 “Technology” according to the General Technology Note for the “development”, “production” or “use” of equipment specified by 5A101.
Part 2 — “INFORMATION SECURITY”
Note 2: Category 5 — Part 2 does not apply to products when accompanying their user for the user’s personal use.
Note 3: Cryptography Note
5A002., 5D002.a.1., 5D002.b. and 5D002.c.1. do not apply to items as follows:
a. Items meeting all of the following:
1. Generally available to the public by being sold, without restriction, from stock at retail selling points by means of any of the following:
a. Over‑the‑counter transactions;
b. Mail order transactions;
c. Electronic transactions; or
d. Telephone call transactions;
2. The cryptographic functionality cannot easily be changed by the user;
3. Designed for installation by the user without further substantial support by the supplier; and
4. Not used
5. When necessary, details of the items are accessible and will be provided, upon request, to the appropriate authority in the exporter’s country in order to ascertain compliance with conditions described in paragraphs 1. to 3. above;
b. Hardware components or ‘executable software’, of existing items described in paragraph a. of this Note, that have been designed for these existing items, and meeting all of the following:
1. “Information security” is not the primary function or set of functions of the component or ‘executable software’;
2. The component or ‘executable software’ does not change any cryptographic functionality of the existing items, or add new cryptographic functionality to the existing items;
3. The feature set of the component or ‘executable software’ is fixed and is not designed or modified to customer specification; and
4. When necessary as determined by the appropriate authority in the exporter’s country, details of the component or ‘executable software’, and details of relevant end‑items are accessible and will be provided to the authority upon request, in order to ascertain compliance with conditions described above.
For the purpose of the Cryptography Note, ‘executable software’ means “software” in executable form, from an existing hardware component excluded from 5A002. by the Cryptography Note.
Note: ‘Executable software’ does not include complete binary images of the “software” running on an end‑item.
Note to the Cryptography Note:
1. To meet paragraph a. of Note 3, all of the following must apply:
a. The item is of potential interest to a wide range of individuals and businesses; and
b. The price and information about the main functionality of the item are available before purchase without the need to consult the vendor or supplier.
2. In determining eligibility of paragraph a. of Note 3, national authorities may take into account relevant factors such as quantity, price, required technical skill, existing sales channels, typical customers, typical use or any exclusionary practices of the supplier.
5A2 Systems, Equipment and Components
CRYPTOGRAPHIC "INFORMATION SECURITY"
5A002 “Information security” systems, equipment and components therefor, as follows:
N.B.: For Global Navigation Satellite Systems (GNSS) receiving equipment containing or employing decryption see 7A005., and for related decryption “software” and “technology” see 7D005. and 7E001.
a. Designed or modified to use ‘cryptography for data confidentiality’ having ‘in excess of 56 bits of symmetric key length, or equivalent’, where that cryptographic capability is usable, has been activated, or can be activated by means of “cryptographic activation” not employing a secure mechanism, as follows:
1. Items having "information security" as a primary function;
2. Digital communication or networking systems, equipment or components, not specified in paragraph 5A002.a.1.;
3. Computers, other items having information storage or processing as a primary function, and components therefor, not specified in paragraphs 5A002.a.1. or 5A002.a.2.;
N.B.: For operating systems, see also 5D002.a.1. and 5D002.c.1.
4. Items, not specified in paragraphs 5A002.a.1. to 5A002.a.3., where the 'cryptography for data confidentiality' having 'in excess of 56 bits of symmetric key length, or equivalent' meets all of the following:
It supports a non‑primary function of the item; and
It is performed by incorporated equipment or "software" that would, as a standalone item, be specified by Category 5 – Part 2.
1. For the purposes of 5A002.a., 'cryptography for data confidentiality’ means “cryptography” that employs digital techniques and performs any cryptographic function other than any of the following:
"Authentication";
Digital signature;
Data integrity;
Non‑repudiation;
Digital rights management, including the execution of copy‑protected "software";
Encryption or decryption in support of entertainment, mass commercial broadcasts or medical records management; or
Key management in support of any function described in paragraph a. to f. above.
For the purposes of 5A00.2.a., ‘in excess of 56 bits of symmetric key length, or equivalent’ means any of the following:
A "symmetric algorithm" employing a key length in excess of 56 bits, not including parity bits; or
An "asymmetric algorithm" where the security of the algorithm is based on any of the following:
1. Factorisation of integers in excess of 512 bits (e.g., RSA);
2. Computation of discrete logarithms in a multiplicative group of a finite field of size greater than 512 bits (e.g., Diffie‑Hellman over Z/pZ); or
3. Discrete logarithms in a group other than mentioned in paragraph b.2. in excess of 112 bits (e.g., Diffie‑Hellman over an elliptic curve).
Note 1: When necessary as determined by the appropriate authority in the exporter's country, details of items must be accessible and provided to the authority upon request, in order to establish any of the following:
Whether the item meets the criteria of 5A002.a.1. to 5A002.a.4.; or
Whether the cryptographic capability for data confidentiality specified by 5A002.a. is usable without "cryptographic activation".
Note 2: 5A002.a. does not apply to any of the following items, or specially designed "information security" components therefor:
a. Smart cards and smart card 'readers/writers' as follows:
1. A smart card or an electronically readable personal document (e.g., token coin, e‑passport) that meets any of the following:
a. The cryptographic capability meets all of the following:
1. It is restricted for use in any of the following:
a. Equipment or systems not described by 5A002.a.1. to 5A002.a.4.;
b. Equipment or systems not using 'cryptography for data confidentiality' having 'in excess of 56 bits of symmetric key length, or equivalent'; or
c. Equipment or systems excluded from 5.A.2.a. by entries b. to f. of this Note; and
2. It cannot be reprogrammed for any other use; or
1. It is specially designed and limited to allow protection of 'personal data' stored within;
2. Has been, or can only be, personalised for public or commercial transactions or individual identification; and
3. Where the cryptographic capability is not user‑accessible;
'Personal data' includes any data specific to a particular person or entity, such as the amount of money stored and data necessary for "authentication".
2. 'Readers/writers' specially designed or modified, and limited, for items specified by paragraph a.1. of this Note;
'Readers/writers' include equipment that communicates with smart cards or electronically readable documents through a network.
b. Cryptographic equipment specially designed and limited for banking use or 'money transactions';
Technical Note
'Money transactions' in 5A002. Note 2.b. includes the collection and settlement of fares or credit functions.
c. Portable or mobile radiotelephones for civil use (e.g., for use with commercial civil cellular radio communication systems) that are not capable of transmitting encrypted data directly to another radiotelephone or equipment (other than Radio Access Network (RAN) equipment), nor of passing encrypted data through RAN equipment (e.g., Radio Network Controller (RNC) or Base Station Controller (BSC));
d. Cordless telephone equipment not capable of end‑to‑end encryption where the maximum effective range of unboosted cordless operation (i.e., a single, unrelayed hop between terminal and home base station) is less than 400 metres according to the manufacturer's specifications;
e. Portable or mobile radiotelephones and similar client wireless devices for civil use, that implement only published or commercial cryptographic standards (except for anti‑piracy functions, which may be non‑published) and also meet the provisions of paragraphs a.2. to a.4. of the Cryptography Note (Note 3 in Category 5 – Part 2), that have been customised for a specific civil industry application with features that do not affect the cryptographic functionality of these original non‑customised devices;
f. Items, where the “information security” functionality is limited to wireless "personal area network" functionality, meeting all of the following:
1. Implement only published or commercial cryptographic standards; and
2. The cryptographic capability is limited to a nominal operating range not exceeding 30 metres according to the manufacturer’s specifications, or not exceeding 100 metres according to the manufacturer’s specifications for equipment that cannot interconnect with more than seven devices;
g. Mobile telecommunications Radio Access Network (RAN) equipment designed for civil use, which also meet the provisions of paragraphs a.2. to a.4. of the Cryptography Note (Note 3 in Category 5 – Part 2), having an RF output power limited to 0.1W (20 dBm) or less, and supporting 16 or fewer concurrent users;
h. Routers, switches or relays, where the "information security" functionality is limited to the tasks of "Operations, Administration or Maintenance" ("OAM") implementing only published or commercial cryptographic standards; or
i. General purpose computing equipment or servers, where the "information security" functionality meets all of the following:
1. Uses only published or commercial cryptographic standards; and
2. Is any of the following:
a. Integral to a CPU that meets the provisions of Note 3 in Category 5 – Part 2;
b. Integral to an operating system that is not specified by 5.D.2.; or
c. Limited to "OAM" of the equipment.
b. Designed or modified for converting, by means of “cryptographic activation”, an item not specified by Category 5 – Part 2 into an item specified by 5A002.a. or 5D002.c.1., and not released by the Cryptography Note (Note 3 in Category 5 – Part 2), or for enabling, by means of “cryptographic activation”, additional functionality specified by 5A002.a. of an item already specified by Category 5 – Part 2;
c. Designed or modified to use or perform "quantum cryptography":
"Quantum cryptography" is also known as Quantum Key Distribution (QKD).
d. Designed or modified to use cryptographic techniques to generate channelising codes, scrambling codes or network identification codes, for systems using ultra‑wideband modulation techniques and having any of the following:
1. A bandwidth exceeding 500 MHz; or
2. A "fractional bandwidth" of 20% or more;
e. Designed or modified to use cryptographic techniques to generate the spreading code for "spread spectrum" systems, not specified by 5.A.2.d., including the hopping code for "frequency hopping" systems.
NON‑CRYPTOGRAPHIC "INFORMATION SECURITY"
5A003 Systems, equipment and components, for non‑cryptographic "information security", as follows:
a. Communications cable systems designed or modified using mechanical, electrical or electronic means to detect surreptitious intrusion;
Note: 5A003.a. applies only to physical layer security. For the purpose of 5.A.3.a., the physical layer includes Layer 1 of the Reference Model of Open Systems Interconnection (OSI) (ISO/IEC 7498‑1).
b. Specially designed or modified to reduce the compromising emanations of information‑bearing signals beyond what is necessary for health, safety or electromagnetic interference standards.
DEFEATING, WEAKENING OR BYPASSING "INFORMATION SECURITY"
5A004 Systems, equipment and components, for defeating, weakening or bypassing "information security", as follows:
a. Designed or modified to perform 'cryptanalytic functions'.
Note: 5A004.a. includes systems or equipment, designed or modified to perform 'cryptanalytic functions' by means of reverse engineering.
'Cryptanalytic functions' are functions designed to defeat cryptographic mechanisms in order to derive confidential variables or sensitive data, including clear text, passwords or cryptographic keys.
5B2 Test, Inspection and Production Equipment
5B002 “Information security” test, inspection and “production” equipment, as follows:
a. Equipment specially designed for the “development” or “production” of equipment specified by 5A002., 5A003., 5A004. or 5B002.b.;
b. Measuring equipment specially designed to evaluate and validate the “information security” functions of the equipment specified by 5A002., 5A003. or 5A004., or of "software" specified by 5D002.a. or 5D002.c.
5C2 Materials
5D2 Software
5D002 “Software” as follows:
a. “Software” specially designed or modified for the “development”, “production” or “use” of any of the following:
1. Equipment specified by 5A002. or "software" specified by 5D002.c.1.;
2. Equipment specified by 5A003. or "software" specified by 5D002.c.2.; or
3. Equipment specified by 5A004. or "software" specified by 5D002.c.3.;
b. “Software” designed or modified for converting, by means of “cryptographic activation”, an item not specified by Category 5 – Part 2 into an item specified by 5A002.a. or 5D002.c.1., and not released by the Cryptography Note (Note 3 in Category 5 – Part 2), or for enabling, by means of “cryptographic activation”, additional functionality specified by 5A002.a. of an item already specified by Category 5 – Part 2;
c. "Software" having the characteristics of, or performing or simulating the functions of, any of the following:
1. Equipment specified by 5A002.a., 5A002.c., 5A002.d. or 5A002.e.;
Note: 5D002.c.1. does not apply to "software" limited to the tasks of "OAM" implementing only published or commercial cryptographic standards.
2. Equipment specified by 5A003.; or
3. Equipment specified by 5A004.
d. Not used.
N.B.: See 5D002.b. for items formerly specified in 5D002.d.
5E2 Technology
5E002 “Technology” as follows:
a. “Technology” according to the General Technology Note for the “development”, “production” or “use” of equipment specified by 5A002., 5A003., 5A004. or 5B002., or of "software" specified by 5D002.a. or 5D002.c.;
b. "Technology" to enable, by means of "cryptographic activation", an item to meet the criteria for functionality specified by 5A002.a. that would not otherwise be met.
Note: 5E002. includes “information security” technical data resulting from procedures carried out to evaluate or determine the implementation of functions, features or techniques specified in Category 5‑Part 2.