Division Propellers - Variable Pitch - Hartzell - AD/PHZL/74 Amdt 2 - Two Blade 'Y" Shank Aluminium Hub - Propellers - Variable Pitch - Hartzell

Propellers - Variable Pitch - Hartzell

AD/PHZL/74 Amdt 2	Two Blade ‘Y” Shank Aluminium Hub	6/2012

<table cellspacing="0" cellpadding="0" style="margin-top:0pt; margin-bottom:0pt; border-collapse:collapse"><tbody><tr><td style="width:74.35pt; padding-right:5.35pt; padding-left:5.35pt; vertical-align:top"><p style="margin-bottom:12pt"><span>Applicability:</span></p><p style="margin-top:12pt"><span></span></p></td><td style="width:414.55pt; padding-right:5.35pt; padding-left:5.35pt; vertical-align:top"><p style="margin-left:21.3pt; margin-bottom:12pt; text-indent:-21.3pt"><span>1.</span><span style="width:12.3pt; text-indent:0pt; display:inline-block"> </span><span>() HC- () 2Y()- () propellers (also known as Y-shank propellers) that have a hub serial number with</span><span> </span><span>“A”, “E”, or no suffix, and installed on or previously installed on:</span></p><p style="margin-top:12pt; margin-left:42.55pt; margin-bottom:12pt; text-indent:-21.3pt"><span>a.</span><span style="width:12.97pt; text-indent:0pt; display:inline-block"> </span><span>Piper PA-32 series aircraft with Textron Lycoming 540 series engines that are rated at 300HP or higher; or</span></p><p style="margin-top:12pt; margin-left:42.55pt; margin-bottom:12pt; text-indent:-21.3pt"><span>b.</span><span style="width:12.3pt; text-indent:0pt; display:inline-block"> </span><span>Pilatus Britten Norman or Britten Norman BN-2 series aircraft (also known as Islander or Trislander) with Textron Lycoming 540 series engines; or</span></p><p style="margin-top:12pt; margin-left:42.55pt; margin-bottom:12pt; text-indent:-21.3pt"><span>c.</span><span style="width:12.97pt; text-indent:0pt; display:inline-block"> </span><span>Any aircraft certified in the aerobatic category; or</span></p><p style="margin-top:12pt; margin-left:42.55pt; margin-bottom:12pt; text-indent:-21.3pt"><span>d.</span><span style="width:12.3pt; text-indent:0pt; display:inline-block"> </span><span>Any aircraft routinely exposed to aerobatic manoeuvres; or</span></p><p style="margin-top:12pt; margin-left:42.55pt; margin-bottom:12pt; text-indent:-21.3pt"><span>e.</span><span style="width:12.97pt; text-indent:0pt; display:inline-block"> </span><span>Any aircraft that has been used for agricultural operations whilst the applicable propeller was installed.</span></p><p class="Note" style="margin-top:12pt; margin-bottom:12pt"><span>Note 1:</span><span> </span><span>This AD </span><span style="font-weight:bold; text-decoration:underline">does not</span><span> apply to propellers with the suffix letter “B” at the end of the hub serial number.</span></p><p class="Note" style="margin-top:12pt; margin-bottom:12pt"><span>Note 2:</span><span> </span><span>Incorporation of a “B” suffix hub will provide terminating action for this Directive.</span></p><p style="margin-top:12pt; margin-left:21.3pt; margin-bottom:12pt; text-indent:-21.3pt"><span>2.</span><span style="width:12.3pt; text-indent:0pt; display:inline-block"> </span><span>() HC- () 2Y()- () propellers S/N’s listed in Table 1:</span></p><p style="margin-top:12pt; text-align:center"><span style="font-weight:bold"></span><span style="font-weight:bold; text-decoration:underline">Table 1. () HC- () 2Y()- () propellers with the following S/N’s</span></p><table cellspacing="0" cellpadding="0" style="margin-top:0pt; margin-left:54pt; margin-bottom:0pt; border:0.75pt solid #000000; border-collapse:collapse"><tbody><tr><td style="width:71.95pt; border-right:0.75pt solid #000000; border-bottom:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3607A</span></p></td><td style="width:71.95pt; border-right:0.75pt solid #000000; border-left:0.75pt solid #000000; border-bottom:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3609A</span></p></td><td style="width:71.95pt; border-right:0.75pt solid #000000; border-left:0.75pt solid #000000; border-bottom:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3613A</span></p></td><td style="width:71.95pt; border-left:0.75pt solid #000000; border-bottom:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3615A</span></p></td></tr><tr><td style="width:71.95pt; border-top:0.75pt solid #000000; border-right:0.75pt solid #000000; border-bottom:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3628A</span></p></td><td style="width:71.95pt; border:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3630A</span></p></td><td style="width:71.95pt; border:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3641A</span></p></td><td style="width:71.95pt; border-top:0.75pt solid #000000; border-left:0.75pt solid #000000; border-bottom:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3940A</span></p></td></tr><tr><td style="width:71.95pt; border-top:0.75pt solid #000000; border-right:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3944A</span></p></td><td style="width:71.95pt; border-top:0.75pt solid #000000; border-right:0.75pt solid #000000; border-left:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3949A</span></p></td><td style="width:71.95pt; border-top:0.75pt solid #000000; border-right:0.75pt solid #000000; border-left:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span>DN3962A</span></p></td><td style="width:71.95pt; border-top:0.75pt solid #000000; border-left:0.75pt solid #000000; padding-right:5.03pt; padding-left:5.03pt; vertical-align:top"><p><span></span></p></td></tr></tbody></table><p class="Note"></p></td></tr></tbody></table>

Requirement:	1. Eddy Current Inspection:a. No Suffix: For propeller hubs without any serial number suffix carry out an Eddy Current Inspection (ECI) of the propeller hub fillet radius for cracks in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.b. If no cracks are found then permanently mark the end of the hub serial number with the suffix “E” in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.c. E Suffix: For propeller hubs with serial number suffix “E” carry out repetitive Eddy Current Inspections (ECI) of the propeller hub fillet radius for cracks in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.d. Table 1: For propeller hubs with a serial number hub listed in Table 1 carry out initial and repetitive ECI as per Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.e. Propeller hubs that are cracked are to be replaced prior to further flight.2. Hub Replacement:a. A Suffix: “A” suffix hubs not listed by serial number in Table 1 shall be removed from service in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.b. Table 1: All hubs listed by serial number in Table 1 shall be removed from service in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.Propeller hubs removed from service as a result of this Directive shall have the hub serial number and type certificate number permanently removed.Previous credit is allowed for inspections, rework, and replacements that were done using the preceding revisions of Hartzell Propeller Inc. SB No. HC-SB-61-227, before the effective date of this AD.
	Note 3: FAA AD 2001-23-08 Amdt 39-12505 refers.Later revisions to Hartzell Propeller Inc. SB No. HC-SB-61-227, Revision 2, dated May 8, 2000, approved by the United States Federal Aviation Administration (FAA) as an Alternative Method of Compliance (AMOC) to FAA 2001-23-08 Amdt39-12505, are considered acceptable for compliance with the equivalent Requirements of this AD.

Requirement:

1. Eddy Current Inspection:a. No Suffix: For propeller hubs without any serial number suffix carry out an Eddy Current Inspection (ECI) of the propeller hub fillet radius for cracks in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.b. If no cracks are found then permanently mark the end of the hub serial number with the suffix “E” in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.c. E Suffix: For propeller hubs with serial number suffix “E” carry out repetitive Eddy Current Inspections (ECI) of the propeller hub fillet radius for cracks in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.d. Table 1: For propeller hubs with a serial number hub listed in Table 1 carry out initial and repetitive ECI as per Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.e. Propeller hubs that are cracked are to be replaced prior to further flight.2. Hub Replacement:a. A Suffix: “A” suffix hubs not listed by serial number in Table 1 shall be removed from service in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.b. Table 1: All hubs listed by serial number in Table 1 shall be removed from service in accordance with Hartzell SB HC-SB-61-227 Revision 5 dated September 28, 2006 or later FAA approved revision.Propeller hubs removed from service as a result of this Directive shall have the hub serial number and type certificate number permanently removed.Previous credit is allowed for inspections, rework, and replacements that were done using the preceding revisions of Hartzell Propeller Inc. SB No. HC-SB-61-227, before the effective date of this AD.

Note 3: FAA AD 2001-23-08 Amdt 39-12505 refers.Later revisions to Hartzell Propeller Inc. SB No. HC-SB-61-227, Revision 2, dated May 8, 2000, approved by the United States Federal Aviation Administration (FAA) as an Alternative Method of Compliance (AMOC) to FAA 2001-23-08 Amdt39-12505, are considered acceptable for compliance with the equivalent Requirements of this AD.

Compliance:	1. Eddy Current Inspection:a. No Suffix: Unless previously carried out; within 50 propeller hours Time In Service (TIS) from the effective date of this Directive.b. E Suffix: At intervals not to exceed 100 propeller hours TIS from the last ECI.c. Table 1: Unless previously carried out within 50 propeller hours TIS, and thereafter at intervals not to exceed 100 hours from the last ECI.
	2. Hub Replacement:a. A Suffix: Propellers with the suffix “A” at the end of the hub serial number excluding those S/N’s listed in Table 1 of applicability, are to be replaced as follows:i. PA-32 and BN-2 series aircraft; at next propeller overhaul but no later than 2000 hours propeller TIS or 31 December 2005, whichever comes first.ii. Aircraft certified in the aerobatic category or aircraft routinely exposed to aerobatic manoeuvres; at next propeller overhaul but not to exceed 1000 propeller hours TIS or 31 December 2005, whichever comes first. For propeller hubs exceeding 1000 hours time in service as of the original effective date of this Directive, remove from service within 15 propeller hours TIS.iii. Agricultural aircraft; at next propeller overhaul, but not to exceed 2000 hours propeller TIS or 31 December 2005, whichever comes first.b. Table 1: At next propeller overhaul but not to exceed 1000 hours propeller TIS or 31 December 2005, whichever comes first. For propeller hubs exceeding 1000 hours TIS as of the original effective date of this Directive, remove from service within 15 hours propeller TIS.Note 4: Installation of the “B” serial number suffix hub will require spinner bulkhead modification per Hartzell Manual 113B or Hartzell Manual 117D dependant on propeller type.
	This Amendment becomes effective on 13 March 2012.

Compliance:

1. Eddy Current Inspection:a. No Suffix: Unless previously carried out; within 50 propeller hours Time In Service (TIS) from the effective date of this Directive.b. E Suffix: At intervals not to exceed 100 propeller hours TIS from the last ECI.c. Table 1: Unless previously carried out within 50 propeller hours TIS, and thereafter at intervals not to exceed 100 hours from the last ECI.

2. Hub Replacement:a. A Suffix: Propellers with the suffix “A” at the end of the hub serial number excluding those S/N’s listed in Table 1 of applicability, are to be replaced as follows:i. PA-32 and BN-2 series aircraft; at next propeller overhaul but no later than 2000 hours propeller TIS or 31 December 2005, whichever comes first.ii. Aircraft certified in the aerobatic category or aircraft routinely exposed to aerobatic manoeuvres; at next propeller overhaul but not to exceed 1000 propeller hours TIS or 31 December 2005, whichever comes first. For propeller hubs exceeding 1000 hours time in service as of the original effective date of this Directive, remove from service within 15 propeller hours TIS.iii. Agricultural aircraft; at next propeller overhaul, but not to exceed 2000 hours propeller TIS or 31 December 2005, whichever comes first.b. Table 1: At next propeller overhaul but not to exceed 1000 hours propeller TIS or 31 December 2005, whichever comes first. For propeller hubs exceeding 1000 hours TIS as of the original effective date of this Directive, remove from service within 15 hours propeller TIS.Note 4: Installation of the “B” serial number suffix hub will require spinner bulkhead modification per Hartzell Manual 113B or Hartzell Manual 117D dependant on propeller type.

This Amendment becomes effective on 13 March 2012.

Background:	There have been incidents of hub cracks in Hartzell two blade "compact" aluminum hub propellers. Existing methods using visual inspection has proven to be unsuccessful in detecting cracks. There have now been cases of blade separation. ECI is now considered the only reliable method for detecting cracks. Cracks typically initiate at the same point on the hub. The cracks originate in the hub at a point adjacent to the blade called the "fillet radius". As the cracks propagate toward the centre of the hub, their progression accelerates and results in failure of one hub half, which can then potentially, progress to blade separation.The original issue of this Airworthiness Directive became effective on 16 May 2002.Amendment 1 introduced a change to include aircraft that can be routinely exposed to aerobatic maneuvers.
	Amendment 2 harmonizes the repetitive inspection interval with the latest revision of the manufacturers service bulletin which is approved as an AMOC with FAA AD 2001-23-08.

Background:

There have been incidents of hub cracks in Hartzell two blade "compact" aluminum hub propellers. Existing methods using visual inspection has proven to be unsuccessful in detecting cracks. There have now been cases of blade separation. ECI is now considered the only reliable method for detecting cracks. Cracks typically initiate at the same point on the hub. The cracks originate in the hub at a point adjacent to the blade called the "fillet radius". As the cracks propagate toward the centre of the hub, their progression accelerates and results in failure of one hub half, which can then potentially, progress to blade separation.The original issue of this Airworthiness Directive became effective on 16 May 2002.Amendment 1 introduced a change to include aircraft that can be routinely exposed to aerobatic maneuvers.

Amendment 2 harmonizes the repetitive inspection interval with the latest revision of the manufacturers service bulletin which is approved as an AMOC with FAA AD 2001-23-08.

Image unavailable in extracted text

Mike Higgins
Delegate of the Civil Aviation Safety Authority

9 March 2012

Propellers - Variable Pitch - Hartzell

Get a plain-English read of Propellers - Variable Pitch - Hartzell

Propellers - Variable Pitch - Hartzell