Division Piper PA-46 (Malibu) Series Aeroplanes - AD/PA-46/32 Amdt 1 - Control Wheel Attachment - Piper PA-46 (Malibu) Series Aeroplanes

Piper PA-46 (Malibu) Series Aeroplanes

AD/PA-46/32 Amdt 1	Control Wheel Attachment	3/2005

Applicability:	Group A aircraft:Models Serial NumbersPA-46-350P Mirage 4636132 through 4636344PA-46-500TP Meridian 4697001 through 4697162Group B aircraft:PA-46-350P Mirage 4636345 through 4636348PA-46-500TP Meridian 4697163 through 4697174
Requirement:	1. For aircraft listed in Group A of the applicability part of this Directive, with the exception of aircraft listed in Group A that are already modified in accordance with the New Piper Aircraft Service Bulletin (SB) No. 1139, dated 28 August 2003; accomplish the following in accordance with Part I of SB No.1139A dated 9 April 2004:a. Inspect the control wheel attachment screw for proper thread engagement (minimum one thread showing past the end of the nut plate), and replace the screw before further flight if insufficient thread engagement is found.b. Inspect the nut plate for sufficient locking characteristics. If the screw can be fully inserted into the nut plate by hand (one thread showing past end of nut), then replacement of the nut plate is required before further flight.c. Reassemble the control wheel onto the control wheel shaft and install the attachment screw using Loctite thread-locking compound.2. For aircraft listed in Group A or Group B of the applicability part of this Directive, install retainer clip part number 104687-002 in accordance with Part II of SB No. 1139A, dated 9 April 2004.Note: Corrected FAA AD 2004-14-12 Amdt 39-13721 refers.

Applicability:

Group A aircraft:Models Serial NumbersPA-46-350P Mirage 4636132 through 4636344PA-46-500TP Meridian 4697001 through 4697162Group B aircraft:PA-46-350P Mirage 4636345 through 4636348PA-46-500TP Meridian 4697163 through 4697174

Requirement:

1. For aircraft listed in Group A of the applicability part of this Directive, with the exception of aircraft listed in Group A that are already modified in accordance with the New Piper Aircraft Service Bulletin (SB) No. 1139, dated 28 August 2003; accomplish the following in accordance with Part I of SB No.1139A dated 9 April 2004:a. Inspect the control wheel attachment screw for proper thread engagement (minimum one thread showing past the end of the nut plate), and replace the screw before further flight if insufficient thread engagement is found.b. Inspect the nut plate for sufficient locking characteristics. If the screw can be fully inserted into the nut plate by hand (one thread showing past end of nut), then replacement of the nut plate is required before further flight.c. Reassemble the control wheel onto the control wheel shaft and install the attachment screw using Loctite thread-locking compound.2. For aircraft listed in Group A or Group B of the applicability part of this Directive, install retainer clip part number 104687-002 in accordance with Part II of SB No. 1139A, dated 9 April 2004.Note: Corrected FAA AD 2004-14-12 Amdt 39-13721 refers.

Compliance:	1. Within 25 hours time in service after 11 August 2004.2. Within 100 hours time in service after 11 August 2004.The compliance times remain unchanged by this issue.
	This Amendment becomes effective on 17 March 2005.
Background:	The FAA received a report that a Model PA-28-181 aircraft crashed after the pilot lost control of the ailerons and elevator. Investigation revealed that the left control wheel single attachment screw had unscrewed from its nut plate, which resulted in the control wheel spinning freely on the control column. Further investigation revealed the screw was too short and the nut plate lacked proper locking characteristics.Amendment 1 is issued in response to the issue of a corrected copy of the related FAA AD, which corrects certain parts of the text. The only part requiring correction of this Directive was Requirement 1. text, “Part I of SB No. 1139 dated 9 April 2004” which was changed to “Part I of SB No. 1139A dated 9 April 2004”.

Compliance:

1. Within 25 hours time in service after 11 August 2004.2. Within 100 hours time in service after 11 August 2004.The compliance times remain unchanged by this issue.

This Amendment becomes effective on 17 March 2005.

Background:

The FAA received a report that a Model PA-28-181 aircraft crashed after the pilot lost control of the ailerons and elevator. Investigation revealed that the left control wheel single attachment screw had unscrewed from its nut plate, which resulted in the control wheel spinning freely on the control column. Further investigation revealed the screw was too short and the nut plate lacked proper locking characteristics.Amendment 1 is issued in response to the issue of a corrected copy of the related FAA AD, which corrects certain parts of the text. The only part requiring correction of this Directive was Requirement 1. text, “Part I of SB No. 1139 dated 9 April 2004” which was changed to “Part I of SB No. 1139A dated 9 April 2004”.

Piper PA-46 (Malibu) Series AeroplanesPiper PA-46 (Malibu) Series Aeroplanes

Get a plain-English read of Piper PA-46 (Malibu) Series Aeroplanes

Piper PA-46 (Malibu) Series Aeroplanes