Commonwealth legislation

AD/PA-30/25 Amdt 3 - Stabilator Torque Tube Bearing Block Attachment Fitting

In ForceCTH

Jurisdiction

Commonwealth

Collection

legislative instrument

Plain English Summary

4/10 complexity

This Directive requires owners/operators of Piper PA‑30 and PA‑39 aircraft (specified serial numbers) to inspect stabilator torque‑tube bearing support fittings for looseness, removing the tailcone and rear access door and manipulating the stabilator. If looseness is found they must fit Piper Kit Part No. 760 835; inspections are due within 100 hours TIS after 15 Sep 1994 and every 100 hours until the kit is fitted to all four fittings, which terminates the inspections. (Requirement; Compliance; Note 1)

JSON API

Deep dive

Want the full deep dive?

Zoe can write the in-depth analysis on top of the summary above: how it works, who it affects and what each part actually does.

Current sections

Direct links to the current provisions in AD/PA-30/25 Amdt 3 - Stabilator Torque Tube Bearing Block Attachment Fitting.

AD/PA-30/25 Amdt 3 - Stabilator Torque Tube Bearing Block Attachment Fitting

COMMONWEALTH OF AUSTRALIA (Civil Aviation Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES

View image in the official source
Piper PA-30 & 39 (Twin Comanche) Series Aeroplanes

AD/PA-30/25

Amdt 3

Stabilator Torque Tube Bearing Block Attachment Fitting

10/94

Applicability: Model PA30 S/No’s 30-1 through 30-2000 and PA39 S/No’s 39-1 through 39-155.

Requirement: 1. Inspect the stabilator torque tube bearing support fittings for looseness by accomplishing the following:

Remove the tailcone and rear aft fuselage access door.

b. Grasp the stabilator tip and exert a fore and aft force and then an up and down force.

c. If looseness is found during the inspection specified above, incorporate Piper Part No. 760 835 (Hi-Shear Rivet Replacement Kit) on the affected fitting.

d. Reinstall the tailcone and right rear aft fuselage access door.

2. Reinspect all stabilator torque tube bearing support fittings on which Piper Kit Part No 760 835 has not been incorporated; in accordance with Requirement 1 of this Directive

Note 1: Incorporating Piper Kit Part No. 760 835 on all four stabilator torque tube bearing support fittings constitutes terminating action for the inspection requirements of this Directive.

Note 2: FAA AD 94-13-10 Amdt 39-8951 and Piper SB 411A refer.

Compliance: 1. Within 100 hours time in service after 15 September 1994, unless Piper Kit Part No. 760 835 is incorporated on all four stabilator torque tube bearing support fittings.

At intervals not to exceed 100 hours time in service, until Piper Kit Part No. 760 835 is incorporated on all four stabilator torque tube bearing support fittings. The compliance of the previous issue of this Directive was “at intervals not exceeding 300 hours time in service”. This amendment is effective from 15 September 1994.

Background: Incidents of looseness of the stabilator torque tube bearing support fittings prompted the issue of this Directive. The actions specified are intended to prevent the loss of pitch control because of looseness of the fittings.

Amendment 3 is issued to align this Directive with the issue of a new FAA AD which specifies reinspection and terminating action criteria.

Source text

Sourced from the Federal Register of Legislation (legislation.gov.au), CC BY 4.0.

1 AD/PA-30/25 Amdt 3 - Stabilator Torque Tube Bearing Block Attachment Fitting