Commonwealth legislation

AD/HU 269/110 Amdt 1 - Tail Rotor Fork Bolt

In ForceCTH

Jurisdiction

Commonwealth

Collection

legislative instrument

Plain English Summary

3/10 complexity

This amendment requires owners/operators of all Schweizer (Hughes) 269 helicopters to replace the tail-rotor fork bolt with a new (zero-time) specified part within 100 flight hours from 1 Aug 2002, then at 1200‑hour intervals, and after any tail-rotor strike. Removed bolts must be inspected, not reused, and cracked bolts reported to CASA. The change permits three alternative part numbers and updates the service bulletin revision; the compliance timing remains unchanged.

JSON API

Deep dive

Want the full deep dive?

Zoe can write the in-depth analysis on top of the summary above: how it works, who it affects and what each part actually does.

Current sections

Direct links to the current provisions in AD/HU 269/110 Amdt 1 - Tail Rotor Fork Bolt.

AD/HU 269/110 Amdt 1 - Tail Rotor Fork Bolt

COMMONWEALTH OF AUSTRALIA (Civil Aviation Safety Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES

View image in the official source

AIRWORTHINESS DIRECTIVE

View image in the official source

For the reasons set out in the background section, the CASA delegate whose signature appears below revokes Airworthiness Directive (AD) AD/HU 269/110 and issues the following AD under subregulation 39.1 (1) of CASR 1998. The AD requires that the action set out in the requirement section (being action that the delegate considers necessary to correct the unsafe condition) be taken in relation to the aircraft or aeronautical product mentioned in the applicability section: (a) in the circumstances mentioned in the requirement section; and (b) in accordance with the instructions set out in the requirement section; and (c) at the time mentioned in the compliance section.

View image in the official source

Schweizer (Hughes) 269 Series Helicopters

AD/HU 269/110

Amdt 1

Tail Rotor Fork Bolt 7/2003

Applicability: All Schweizer (Hughes) 269 series helicopters.

Requirement: Remove the tail rotor fork bolt and replace with a new (zero time) bolt P/N 269A6092-3, P/N 369A1602-3 or P/N 6092-3 in accordance with Schweizer SB

B-269 Revision 1. Inspect the removed bolt for excessive wear, gouges, scoring or cracks. Do not re- use any removed bolts. If any cracks are found, report them to CASA by defect report and retain the bolt for later analysis.

If a tail rotor strike occurs during service, the tail rotor fork bolt must be removed and replaced with a new (zero time) bolt.

Compliance: Within 100 hours time in Service after 1 August 2002 and thereafter at 1200 hour intervals.

This Amendment becomes effective on 10 July 2003.

Background: A recent incident occurred where severe tail rotor vibration was encountered. The cause was found to be a broken tail rotor fork bolt. On investigation, the bolt was found to have suffered a corrosion related fatigue failure, which was not detectable during normal visual inspection of the tail rotor hub. Examination of a second bolt removed from another aircraft revealed severe fretting and corrosion. Tail rotor fork bolt failure may result in loss of the tail rotor during flight.

This amendment allows the use of any of three different part number bolts, when replacing the tail rotor fork bolt. It also updates the revision status of the requirement document. There is no change to the compliance.

The original issue of this Airworthiness Directive became effective on 17 July 2002.

View image in the official source

David Villiers

View image in the official sourceDelegate of the Civil Aviation Safety Authority 20 May 2003

The above AD is notified in the Commonwealth of Australia Gazette on 18 June 2003.

Page 1 of 1

Source text

Sourced from the Federal Register of Legislation (legislation.gov.au), CC BY 4.0.

1 AD/HU 269/110 Amdt 1 - Tail Rotor Fork Bolt

COMMONWEALTH OF AUSTRALIA (Civil Aviation Safety Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES

AIRWORTHINESS DIRECTIVE

Schweizer (Hughes) 269 Series Helicopters

AD/HU 269/110

Amdt 1

Tail Rotor Fork Bolt 7/2003

Applicability: All Schweizer (Hughes) 269 series helicopters.

Requirement: Remove the tail rotor fork bolt and replace with a new (zero time) bolt P/N 269A6092-3, P/N 369A1602-3 or P/N 6092-3 in accordance with Schweizer SB

If a tail rotor strike occurs during service, the tail rotor fork bolt must be removed and replaced with a new (zero time) bolt.

Compliance: Within 100 hours time in Service after 1 August 2002 and thereafter at 1200 hour intervals.

This Amendment becomes effective on 10 July 2003.