Commonwealth legislation

AD/GAF-N22/56 Amdt 1 - Rudder Pedal Pivot Arms

In ForceCTH

Jurisdiction

Commonwealth

Collection

legislative instrument

Plain English Summary

6/10 complexity

This airworthiness directive requires owners/operators of GAF N22 and N24 aeroplanes to inspect rudder pedal pivot arms for cracking and internal corrosion, and to repair, treat or scrap parts as specified. It imposes different inspection methods and intervals depending on whether modification N794 is fitted, mandates dye‑penetrant inspection and internal corrosion treatment for unmodified arms, and a 10× visual check for modified arms to reduce the risk of rudder control impairment.

JSON API

Deep dive

Want the full deep dive?

Zoe can write the in-depth analysis on top of the summary above: how it works, who it affects and what each part actually does.

Current sections

Direct links to the current provisions in AD/GAF-N22/56 Amdt 1 - Rudder Pedal Pivot Arms.

AD/GAF-N22/56 Amdt 1 - Rudder Pedal Pivot Arms

COMMONWEALTH OF AUSTRALIA (Civil Aviation Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES

View image in the official source
GAF N22 and N24 Series Aeroplanes

AD/GAF-N22/56

Amdt 1

Rudder Pedal Pivot Arms 10/95

Applicability: All N22 and N24 aircraft (including pre Mod N33 configuration). Requirement: 1. For pre Mod N794 Rudder Pedal Pivot Arms:-

(a) Remove the rudder pedal pivot arms from the aircraft and perform a fluorescent dye penetrant inspection around the shaft housing in accordance with ASTA Service Bulletin ANMD-27-42, Revision 3, Accomplishment Instructions A.Part 1.(1).

(b) Treat the inside of the rudder pedal pivot arms for corrosion in accordance with ASTA Service Bulletin ANMD-27-42, Revision 3, Accomplishment Instructions B.Part 2.(6),(12)&(13).

It is recommended that Mod N794 be incorporated in its entirety at this time. If Mod N794 is incorporated at a later time, it will be necessary to repeat the corrosion protection treatment after welding. Pedal pivot arms exhibiting severe corrosion, in the form of loose rust flakes or severe pitting, are to be scrapped.

2. For post Mod N794 Rudder Pedal Pivot Arms:-

(a) Visually inspect the rudder pedal pivot arms using 10x magnification, in accordance with ASTA Service Bulletin ANMD-27-42, Revision 3, Accomplishment Instructions A.Part 1.(2).

Compliance: 1. (a) Action in accordance with Requirement paragraph 1(a) before 1000 hours component time in service, or before 14 October 1995, whichever occurs last. Repeat the inspection at intervals not to exceed 300 hours component time in service.

(b) Unless previously done, action in accordance with Requirement paragraph 1(b) not later than the next fluorescent dye penetrant inspection after 30 September 1995.

2. Action in accordance with Requirement paragraph 2 at intervals not exceeding 1800 hours component time in service or before 14 October 1995, whichever occurs last.

Background: Major defect reports have been received of cracking in both pilot and co-pilot rudder pedal pivot arms at times in service as low as 1400 hours. If not detected, cracks could progress to a point where aircraft control may be impeded. The omission of internal corrosion treatment at manufacture, and subsequent internal corrosion, exacerbates the problem. This Amendment reduces the inspection threshold and introduces a corrosion treatment for unmodified arms, and introduces a visual inspection for modified arms.

COMMONWEALTH OF AUSTRALIA (Civil Aviation Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES

Source text

Sourced from the Federal Register of Legislation (legislation.gov.au), CC BY 4.0.

1 AD/GAF-N22/56 Amdt 1 - Rudder Pedal Pivot Arms

COMMONWEALTH OF AUSTRALIA (Civil Aviation Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES

GAF N22 and N24 Series Aeroplanes

AD/GAF-N22/56

Amdt 1

Rudder Pedal Pivot Arms 10/95

Applicability: All N22 and N24 aircraft (including pre Mod N33 configuration). Requirement: 1. For pre Mod N794 Rudder Pedal Pivot Arms:-

(a) Remove the rudder pedal pivot arms from the aircraft and perform a fluorescent dye penetrant inspection around the shaft housing in accordance with ASTA Service Bulletin ANMD-27-42, Revision 3, Accomplishment Instructions A.Part 1.(1).

(b) Treat the inside of the rudder pedal pivot arms for corrosion in accordance with ASTA Service Bulletin ANMD-27-42, Revision 3, Accomplishment Instructions B.Part 2.(6),(12)&(13).

2. For post Mod N794 Rudder Pedal Pivot Arms:-

(a) Visually inspect the rudder pedal pivot arms using 10x magnification, in accordance with ASTA Service Bulletin ANMD-27-42, Revision 3, Accomplishment Instructions A.Part 1.(2).

(b) Unless previously done, action in accordance with Requirement paragraph 1(b) not later than the next fluorescent dye penetrant inspection after 30 September 1995.

2. Action in accordance with Requirement paragraph 2 at intervals not exceeding 1800 hours component time in service or before 14 October 1995, whichever occurs last.