Commonwealth legislation

AD/CESSNA 180/81 - Fuel Strainer

In ForceCTH

Jurisdiction

Commonwealth

Collection

legislative instrument

Plain English Summary

3/10 complexity

Requires inspection of the fuel strainer assembly on specified Cessna 180/182 series aircraft for certain part numbers shipped between 12 Dec 1996 and 5 Sep 1997. The standpipe must measure no more than 1.68 inches per Cessna SEB97‑9; if it exceeds that length the top assembly must be replaced before further flight. Owners/operators pay for inspection and any replacement. A licensed pilot may check aircraft records to confirm whether the AD applies. Inspections are due within 12 months; replacements before next flight.

JSON API

Deep dive

Want the full deep dive?

Zoe can write the in-depth analysis on top of the summary above: how it works, who it affects and what each part actually does.

Current sections

Direct links to the current provisions in AD/CESSNA 180/81 - Fuel Strainer.

AIRWORTHINESS DIRECTIVE

View image in the official source

View image in the official source
For the reasons set out in the background section, the CASA delegate whose signature appears below issues the following Airworthiness Directive (AD) under subregulation 39.1 (1) of CAR 1998. The AD requires that the action set out in the requirement section (being action that the delegate considers necessary to correct the unsafe condition) be taken in relation to the aircraft or aeronautical product mentioned in the applicability section: (a) in the circumstances mentioned in the requirement section; and (b) in accordance with the instructions set out in the requirement section; and (c) at the time mentioned in the compliance section.

AD/CESSNA 180/81 Fuel Strainer 7/2000

Applicability: Models 180H, 180J, 180K, 182H, 182J, 182K, 182L, 182M, 182N, 182P, 182Q, 182R/T182, 182R, R182, R182/TR182, A182J, A182K, A182L, A182N, F182P,

F182Q and FR182, series aircraft.

Requirement: 1. Inspect aircraft fuel strainer assembly. If P/N 0756005-2 top assembly, P/N 0756005-8 or 0756005-9 fuel strainer assembly were shipped from Cessna between December 12, 1996 and September 5, 1997, and fitted to the aircraft, measure the standby pipe in the fuel strainer assembly for a visible maximum length not exceeding 1.68 inches, in accordance with the Accomplishment Instructions of Cessna Single Engine Service Bulletin SEB97-9 dated November 17,1997.

The holder of a pilot licence, other than a student pilot, valid for the aircraft type, may review the aircraft records to determine if parts listed in this Directive have been fitted to the aircraft. If this review concludes that parts listed in this Directive have not been fitted then a certification stating that “This Directive does not apply as no parts listed in the Cessna SEB97-9 have been fitted to this aircraft.” may be entered in the aircraft records.

Replace the filter strainer top assembly if the standpipe tube exceeds the specified measurement.

Note: FAA AD 2000-06-01 Amendment 39-11641 refers.

Compliance: 1. Unless previously accomplished, within 12 calendar months time in service from the effective date of this Directive.

Prior to further flight.

This Airworthiness Directive becomes effective on 13 July 2000.

Source text

Sourced from the Federal Register of Legislation (legislation.gov.au), CC BY 4.0.

AIRWORTHINESS DIRECTIVE AIRWORTHINESS DIRECTIVE

AIRWORTHINESS DIRECTIVE

For the reasons set out in the background section, the CASA delegate whose signature appears below issues the following Airworthiness Directive (AD) under subregulation 39.1 (1) of CAR 1998. The AD requires that the action set out in the requirement section (being action that the delegate considers necessary to correct the unsafe condition) be taken in relation to the aircraft or aeronautical product mentioned in the applicability section: (a) in the circumstances mentioned in the requirement section; and (b) in accordance with the instructions set out in the requirement section; and (c) at the time mentioned in the compliance section.