1AD/BEECH 35/58 Amdt 6 - Empennage Structural Integrity

Image unavailable in extracted text

AIRWORTHINESS DIRECTIVE

Image unavailable in extracted text

For the reasons set out in the background section, the CASA delegate whose signature appears below revokes Airworthiness Directive (AD) AD/BEECH 35/58 Amdt 5 and issues the following AD under subregulation 39.1 (1) of CASR 1998. The AD requires that the action set out in the requirement section (being action that the delegate considers necessary to correct the unsafe condition) be taken in relation to the aircraft or aeronautical product mentioned in the applicability section: (a) in the circumstances mentioned in the requirement section; and (b) in accordance with the instructions set out in the requirement section; and (c) at the time mentioned in the compliance section.

Image unavailable in extracted text

Beechcraft 35 (Bonanza) Series Aeroplanes

AD/BEECH 35/58

Amdt 6

Empennage Structural Integrity 10/2003

Applicability: All Model C35, D35, E35, F35, G35, H35, J35, K35, M35, N35, and P35 aircraft.

All Model S35, V35, V35A, and V35B aircraft, that do not have the straight tail conversion modification incorporated in accordance with Supplemental Type Certificate (STC) SA2149CE.

Requirement: 1. Verify that the ruddervator balance is within the manufacturer’s specified limits as defined in the applicable shop or maintenance manual. If the ruddervator is found outside the specified limits, before further flight, balance the ruddervator control surfaces in accordance with Section 3 of Beech Shop Manual 35- 590096B19, or subsequent revisions.

2. Visually inspect the empennage, aft fuselage, and ruddervator control system for damage, in accordance with the procedures and as specified in the instructions to Beech Kit 35-4017-1 “Kit information Empennage and Aft Fuselage Inspection”, as specified in Beech Service Bulletin No. 2188, dated May 1987.

Repair or replace any damaged parts; and,

b. Set the elevator controls, rudder and tab system controls, cable tensions, and rigging.

3. Accomplish the following actions in accordance with the procedures in the instructions to Beech Kit 35-4017-1 “Kit Information Empennage & Aft Fuselage Inspection”, as specified in Beech Service Bulletin No. 2188:

Visually inspect the fuselage bulkheads at Fuselage Station (FS) 256.9 and FS 272 for damage (cracks, distortion, loose rivets, etc.).

b. Visually inspect the fuselage skin around the bulkhead for damage (wrinkles or cracks).

c. Repair or replace damaged parts, before further flight, after the inspection where damage is found.

4. Remove all external stabiliser reinforcements installed during incorporation of either STC SA845GL, STC SA846GL, STC SA1650CE, STC SA2286NM, or STC SA2287NM, as applicable; in accordance with the applicable maintenance information.

Seal and fill any residual holes with appropriate size rivets.

b. The internal stub spar incorporated through STC SA1649CE and STC SA1650CE may be retained.

c. The external angles incorporated through STC SA1649CE may also be retained by properly trimming the leading edges section to permit installation of the stabiliser reinforcement referenced in Requirement paragraph 5.a. of this Directive.

d. For the Beech Models S35, V35, V35A, and V35B aircraft, the tail-safe external angles that were installed in accordance with STC SA1649CE may be retained and used instead of the stabiliser reinforcement specified in Requirement paragraph 5.a. of this Directive.

5. Accomplish the following in accordance with the instructions to RAC Kit No. 35-4016-3, 35-4016-5, 35-4016-7, or 35-4016-9, as applicable, and as specified in Beech SB No. 2188:

Install stabiliser reinforcements;

b. Set the elevator nose-down trim; and.

c. Replace the ruddervator tab control cables with larger diameter cables.

6. Verify the accuracy of the aircraft basic weight and balance information and correct any discrepancies, in accordance with the following procedures:

Weight and Balance Accuracy Method No.1:

Review existing weight and balance documentation to assure completeness and accuracy of the documentation from the most recent approved weighing or from factory delivery to date of compliance with this Directive.

ii. Compare the actual configuration of the aircraft to the configuration described in the weight and balance documentation.

iii. If equipment additions or deletions are not reflected in the documentation or if modifications affecting the location of the centre of gravity (eg. paint or structural repairs) are not documented, determine the accuracy of the aircraft weight and balance data in accordance with Method No.2.

b. Weight and Balance Information Accuracy Method No.2:

Determine the basic empty weight and centre of gravity (CG) of the empty aircraft using the Weighing Instructions in the Weight and Balance section of the aircraft flight manual/pilot’s operating handbook (AFM/POH).

ii. Record the results in the aircraft records, and use these new values as the basis for computing the weight and CG information as specified in the Weight and Balance section of the AFM/POH.