Commonwealth legislation

AD/BEECH 1900/26 - MLG Actuator End Cap

In ForceCTH

Jurisdiction

Commonwealth

Collection

legislative instrument

Plain English Summary

4/10 complexity

Beechcraft 1900 operators must inspect main landing‑gear hydraulic actuators for two specific Frisby Aerospace end‑cap part numbers and, if found, remove them and either replace them with approved parts or rework them per the referenced service bulletins before further flight. The Directive responds to reported fatigue cracks in the actuator end cap and aims to reduce the risk of the landing gear failing to lock during landing, taxi or ground operations.

JSON API

Deep dive

Want the full deep dive?

Zoe can write the in-depth analysis on top of the summary above: how it works, who it affects and what each part actually does.

Current sections

Direct links to the current provisions in AD/BEECH 1900/26 - MLG Actuator End Cap.

AD/BEECH 1900/26 - MLG Actuator End Cap

COMMONWEALTH OF AUSTRALIA (Civil Aviation Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES

View image in the official source
Beechcraft 1900 Series Aeroplanes

AD/BEECH 1900/26 MLG Actuator End Cap 4/99

Applicability: Model Serial Numbers

1900 UA-2 and UA-3

1900C UB-1 through UB-74, and UC-1 through UC-174

1900C (C-12J) UD-1 through UD-6

1900D UE-1 through UE-299

Requirement: Inspect the main landing gear hydraulic actuators to determine whether any Frisby Aerospace actuator, part number (P/N) 114-380041-11 or P/N 114-380041-13 is installed. Accomplish this inspection in accordance with Raytheon Mandatory Service Bulletin (MSB) SB.32-3141.

If any Frisby Aerospace actuator, P/N 114-380041-11 or P/N 114-380041-13 is installed, before further flight, remove it and accomplish one of the following:

Replace the Frisby Aerospace actuator with one of a part number listed in the Material Information section of Raytheon MSB SB.32-3141. Accomplish this replacement in accordance with the applicable maintenance manual; or,

2. Rework the Frisby Aerospace actuator by incorporating the kit referenced in the Material Information section of Raytheon MSB SB.32-3141. Accomplish this rework in accordance with Frisby Aerospace Service Bulletin 1FA10043-0001, dated October 1997.

Note: FAA AD 99-04-08 Amdt 39-11032 refers.

Compliance: Hours Time-in-Service (TIS) on the

MLG Actuator

Inspection Compliance Times after 22 April 1999

Less than 6,000 hours TIS Upon accumulating 6,600 hours TIS on the actuator or within the next 600 hours TIS, whichever occurs later

6,000 hours TIS through 6,999 hours TIS Within the next 600 hours TIS 7,000 hours TIS through 7,999 hours TIS Within the next 500 hours TIS 8,000 hours TIS through 8,999 hours TIS Within the next 400 hours TIS 9,000 hours TIS through 9,999 hours TIS Within the next 300 hours TIS 10,000 hours TIS or more Within the next 200 hours TIS This Airworthiness Directive becomes effective on 22 April 1999.

COMMONWEALTH OF AUSTRALIA (Civil Aviation Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES

Background: The FAA received reports of fatigue cracks in the end cap of main landing gear hydraulic actuators manufactured by Frisby Aerospace and installed on the affected aircraft. The actions specified by this Directive are intended to prevent the main landing gear from failing to lock down due to the hydraulic actuator cracking and separating, which could result in loss of control of the aircraft during landing, taxi, or ground operations.

Source text

Sourced from the Federal Register of Legislation (legislation.gov.au), CC BY 4.0.

1 AD/BEECH 1900/26 - MLG Actuator End Cap

COMMONWEALTH OF AUSTRALIA (Civil Aviation Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES

Beechcraft 1900 Series Aeroplanes

AD/BEECH 1900/26 MLG Actuator End Cap 4/99

Applicability: Model Serial Numbers

1900 UA-2 and UA-3

1900C UB-1 through UB-74, and UC-1 through UC-174

1900C (C-12J) UD-1 through UD-6

1900D UE-1 through UE-299

If any Frisby Aerospace actuator, P/N 114-380041-11 or P/N 114-380041-13 is installed, before further flight, remove it and accomplish one of the following:

Replace the Frisby Aerospace actuator with one of a part number listed in the Material Information section of Raytheon MSB SB.32-3141. Accomplish this replacement in accordance with the applicable maintenance manual; or,

2. Rework the Frisby Aerospace actuator by incorporating the kit referenced in the Material Information section of Raytheon MSB SB.32-3141. Accomplish this rework in accordance with Frisby Aerospace Service Bulletin 1FA10043-0001, dated October 1997.

Note: FAA AD 99-04-08 Amdt 39-11032 refers.

Compliance: Hours Time-in-Service (TIS) on the

MLG Actuator

Inspection Compliance Times after 22 April 1999

Less than 6,000 hours TIS Upon accumulating 6,600 hours TIS on the actuator or within the next 600 hours TIS, whichever occurs later

COMMONWEALTH OF AUSTRALIA (Civil Aviation Regulations 1998), PART 39 - 105 CIVIL AVIATION SAFETY AUTHORITY

SCHEDULE OF AIRWORTHINESS DIRECTIVES