sec.705CBReview

### sec.705CB Review This section applies if— it is proposed to change a joint interaction management plan; or a change in the overlapping area, or at an operating plant in the overlapping area, is likely to give rise to an additional risk to safety or health in the overlapping area or at the plant; or any of the following circumstances exist— an additional risk to safety or health in the overlapping area, or at an operating plant in the overlapping area, is identified; consultation with workers indicates a review is necessary; a risk control measure did not control the risk it was intended to control to an acceptable level. For subsection (1) (b) , a change in the overlapping area, or at an operating plant in the overlapping area, includes— a change to any aspect of the overlapping area or the plant itself; and a change to a system of work, process or procedure in the overlapping area or at the plant. The operator of the authorised activities operating plant must review and, if necessary, revise the joint interaction management plan. Maximum penalty—200 penalty units. The review must take place in consultation with the operators of each operating plant in the overlapping area, the site senior executive and any other workers to the extent they are affected by the matters under review. Maximum penalty—200 penalty units. The review must take place— for subsection (1) (a) or (b) —before the change to the joint interaction management plan is made; or for subsection (1) (c) —as soon as possible after the circumstance exists. Maximum penalty—200 penalty units. A revision of the plan under subsection (3) must be recorded on the plan. Maximum penalty—200 penalty units. If the operator of the authorised activities operating plant and the site senior executive can not agree on the content of a revision of the plan, either party may apply for arbitration of the dispute. s 705CB ins 2014 No. 64 s 228 (sec.705CB-ssec.1) This section applies if— it is proposed to change a joint interaction management plan; or a change in the overlapping area, or at an operating plant in the overlapping area, is likely to give rise to an additional risk to safety or health in the overlapping area or at the plant; or any of the following circumstances exist— an additional risk to safety or health in the overlapping area, or at an operating plant in the overlapping area, is identified; consultation with workers indicates a review is necessary; a risk control measure did not control the risk it was intended to control to an acceptable level. (sec.705CB-ssec.2) For subsection (1) (b) , a change in the overlapping area, or at an operating plant in the overlapping area, includes— a change to any aspect of the overlapping area or the plant itself; and a change to a system of work, process or procedure in the overlapping area or at the plant. (sec.705CB-ssec.3) The operator of the authorised activities operating plant must review and, if necessary, revise the joint interaction management plan. Maximum penalty—200 penalty units. (sec.705CB-ssec.4) The review must take place in consultation with the operators of each operating plant in the overlapping area, the site senior executive and any other workers to the extent they are affected by the matters under review. Maximum penalty—200 penalty units. (sec.705CB-ssec.5) The review must take place— for subsection (1) (a) or (b) —before the change to the joint interaction management plan is made; or for subsection (1) (c) —as soon as possible after the circumstance exists. Maximum penalty—200 penalty units. (sec.705CB-ssec.6) A revision of the plan under subsection (3) must be recorded on the plan. Maximum penalty—200 penalty units. (sec.705CB-ssec.7) If the operator of the authorised activities operating plant and the site senior executive can not agree on the content of a revision of the plan, either party may apply for arbitration of the dispute. - (a) it is proposed to change a joint interaction management plan; or - (b) a change in the overlapping area, or at an operating plant in the overlapping area, is likely to give rise to an additional risk to safety or health in the overlapping area or at the plant; or - (c) any of the following circumstances exist— (i) an additional risk to safety or health in the overlapping area, or at an operating plant in the overlapping area, is identified; (ii) consultation with workers indicates a review is necessary; (iii) a risk control measure did not control the risk it was intended to control to an acceptable level. - (i) an additional risk to safety or health in the overlapping area, or at an operating plant in the overlapping area, is identified; - (ii) consultation with workers indicates a review is necessary; - (iii) a risk control measure did not control the risk it was intended to control to an acceptable level. - (i) an additional risk to safety or health in the overlapping area, or at an operating plant in the overlapping area, is identified; - (ii) consultation with workers indicates a review is necessary; - (iii) a risk control measure did not control the risk it was intended to control to an acceptable level. - (a) a change to any aspect of the overlapping area or the plant itself; and - (b) a change to a system of work, process or procedure in the overlapping area or at the plant. - (a) for subsection (1) (a) or (b) —before the change to the joint interaction management plan is made; or - (b) for subsection (1) (c) —as soon as possible after the circumstance exists.